RGB790BEK5BB Hotpoint Range - Instructions

This was a real easy repair. The key is to remove the door (by lifting straight up) and remove the bottom drawer. Then take all the trays out of the oven, using a screw driver remove the bottom pan that hides the burner and igniter. From underneath the oven (ie drawer space) use a screw driver to disconnect two screws that hold the burner assembly against the back wall of the oven. Then remove the one screw from inside the oven that holds the burner assembly (its close to the door area). Unplug the two igniter wires from underneath the oven and then lift out the entire burner assembly. Take off the two screws that hold the old igniter to the burner and replace with new igniter. Make sure you mark the wires when you remove them because you need the connectors on the end for the new wire. Then give yourself plenty of wire, cut the old wire off the old igniter and using the provided wire ties join them to the new igniter wires and reconnect everything. Sounds complicated but it took me about 20 minutes and its really an easy repair. Good luck.

took drawer out removed broken guide. It had 1 screw removed it put the new guide in place put screw back in. Put drawer back in stove, It works fine.

On each side of the door at the top you will find an allen screw, remove those to remove the cover plate. This will prevent the new glass from sitting flush with the door, if not removed. On the inside of the door, you will find two more silver hex screws, these release the glass frame. On the flimsy part that seperates from the main door frame, there are two small brackets that hold the glass panel at the bottom of the door. Carefully pry out all the ramaining glass shards, and believe me they are there, so be very careful and vacuum up immediately to prevent cuts later. The glass frame will be very wobbly, so position yourself in front and place one knee up to support the frame and place the new glass panel in the bottom slot first, then just hold it up, and reinstall the top brackets. These fit tightly on the glass, so expect to have to push a bit. Now reinstall the screws, fold both parts together, use the silver screws to reconnect the glass panel assembly to the door frame.My oven door handle never had to come off.

Replaced old with new.

I was a bit hesitant to perform this repair but attempted it due to the other write-ups which were very helpful. The repair went very well and was quite easy. There was a suggestion to remove the gas defuser (the pipe thing that has the igniter attached), I believe loosening this defuser made the whole repair so much easer and quicker. Trying to remove the two screws that hold the igniter without this approach would have been very difficult. I was hesitant to do this but removing the 3 screws that hold the defuser in place was not a problem at all.

1. Removed oven door.
2. Removed shelves.
3. Removed oven bottom.
4. Removed pan drawer.
5. Removed the 2 burner mounting nuts at back of oven pan drawer opening.
6. Removed top burner nut.
7. Pulled igniter out from top.
8. Snipped igniter wires.
9. Removed igniter from burner
10. Attached new ignitor wires with the enclosed wire nuts.
11. Attached new igniter to burner.
12. Replaced burner.
13. Pushed excess wire out of the oven through opening at back of pan drawer.
14. Reinstalled burner mounting nuts at back of drawer.
15. Reinstalled burner nut at top of burner
16. Reinstalled oven bottom, oven door and pan drawer.

took nut driver to remove the old and replaced with new. simple.

Unplug the range from its wall socket to avoid electric shock. The various range parts that support a pot or frypan are easily lifted off their perches, exposing the small white igniter. The only moderately difficult aspect is wiggling the igniter out of its retainer. The electric wire leading into it then can be pulled out and fed into the new igniter with a push. Replace igniter in its retainer, then replace the range parts you removed to expose the igniter and plug the range back into the wall socket. Piece of cake.

Unplugged the electrical.Removed the door, removed the oven racks and removed the bottom pan. Removed the wire nuts from the two wires. Removed the burner tube. Removed the Igniter. Installed in reverse order. It was very easy however it was the third igniter that I had to replace in this range so I was used to it.

Order parts and installed - no tools needed - completed repairs less than 1 minute

Removed oven base plate by removing 2 screws and lifting out of oven. Pulled out bottom drawer and disconnected two wires from igniter. Removed 2 screws connecting burner to oven wall. Back to oven inside, and removed screw holding burner to oven bottom. Took burner out if oven. Removed 2 screws securing igniter to burner. Secured new igniter to burner. Reversed steps to put all parts back. Oven works fine.

Simple swap and go.Several wires had different locations but every thing was marked well on both panels.Did one wire at a time.Took about 45min from pulling out oven to pushing back in.Just wish I had known about your site years ago.

slid the old ones out and slid the new ones in. done

Hired gas company to do repairs for safety reasons

Replaced the old with the new parts...stove like new...very pleased with the improved function and appearance of stove.