RB525DD1CC Hotpoint Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Wiley from Port Orchard, WA
- Parts Used:
- WB30X46987
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
The bake element quit working.
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I then connected the wires to the new element and reinstalled the two screws. A brief test showed the element worked and that was it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- CLYDE from SAINT PETERSBURG, FL
- Parts Used:
- WB30X46987
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
every thing went great
every thing went great
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Emmett J from Winchester, VA
- Parts Used:
- WB17T10006
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
terminal was broken due to maney uses
unscrew the terminal block,pulled the old wires out,installed the new wires installed the new block
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from SPRINGFIELD, OR
- Parts Used:
- WB30X46987, WB30X46986
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers, Socket set
When I took out the baking element, the wires went up inside because they were so short, I got a hold of one of them but couldn't get a hold of the other.
Had to pull out the refrigerator and put it in the dining room in order to pull out the stove to be able to get to the back of it. Had to take off the back of the stove to get to the wiring for the baking element, so at that point I replaced the broil element at the same time. Not a easy job at all.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- fran from harrisburg, PA
- Parts Used:
- WB30X46987
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
a pan was dropped on hot bake element,,bake element broke
i dd not notice at first and started the self cleaner,,,i notice the self cleaner did not work,the screws had to be sprayed with dw30a couple of times and a pair of pliers to remove screws(no wrench set)after removing screws pulled the wires out to see and removed the connection to wires,,,replaced with new bake element and replaced the screws works fine,,,by the way i am a 64 years old grandmother
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nancy from RUSH, NY
- Parts Used:
- WB30X46987
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Oven coil burned out
Removed the hexagon screws. pulled the unit out and wiggled the tabs loose disconnecting them. Installed the new unit-attaching the tabs making sure they were tight. Put the new unit through the opening in the back of the oven and reattached the hexagon screws. Back in business in about 10 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kelly from Charlotte, NC
- Parts Used:
- WB30X46987
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Baking element not getting hot
First my son removed the two screws that held th element in place but first please tell everyone to turn off the breaker first. My son did not and he had gotten a shock from this and burned his hand. I think this is very important first. After cleaning up his hand he then replaced the element and tested it and it worked nicely.
Thank you for your prompt delivery and the correct part.
Sincerely
Kelly Didsbury
Thank you for your prompt delivery and the correct part.
Sincerely
Kelly Didsbury
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Buddy from Georgetown, IN
- Parts Used:
- WB30X46987
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Burned ou element
Removed two screws, and replaced element with a new one. Easy, works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- TERESA from SALTVILLE, VA
- Parts Used:
- WB02K10061
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Drawer glide broken
took nut driver to remove the old and replaced with new. simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sandy from PALMER, MA
- Parts Used:
- WB30X46987
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
the old element bunt out.
Followed the video and it was fast and quick.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from CHANNELVIEW, TX
- Parts Used:
- WB24T10027
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Replace Surface Burner Switch
Unplug stove.
Remove rear panel of stove with a nut driver or socket. Remove knob from switch and use small screwdriver to remove screws on front panel switch. Remove and replace each wire contact one at a time to ensure correct wiring configuration. Replace screws on front panel to secure switch. Plug stove in and check that it works properly. Replace rear panel and move stove back in place.
Remove rear panel of stove with a nut driver or socket. Remove knob from switch and use small screwdriver to remove screws on front panel switch. Remove and replace each wire contact one at a time to ensure correct wiring configuration. Replace screws on front panel to secure switch. Plug stove in and check that it works properly. Replace rear panel and move stove back in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marco from Santa Barbara, CA
- Parts Used:
- WB17T10006
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Two sockets for electric elements and their end terminals were badly burned.
0) Take the back cover of the range off.
1) Carefully noted how the wires and the sockets were connected.
2) Visually checked that the new parts were practically identical old ones.
3) Put together the new sockets from the parts in the kit.
4) disconnect the old sockets and put the new sockets in place.
5) For each unit disconnect one old wire at the time and connect the new wire. Repeat the same for second wire.
6) Neatly bunch together the rest of the wires with electrical tape. Do not cut the wires!
That's it! It took about 20-30 minutes.
1) Carefully noted how the wires and the sockets were connected.
2) Visually checked that the new parts were practically identical old ones.
3) Put together the new sockets from the parts in the kit.
4) disconnect the old sockets and put the new sockets in place.
5) For each unit disconnect one old wire at the time and connect the new wire. Repeat the same for second wire.
6) Neatly bunch together the rest of the wires with electrical tape. Do not cut the wires!
That's it! It took about 20-30 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ryan from NOVATO, CA
- Parts Used:
- WB30X46987
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven heating element broke
Turn off the power at the breaker. Use hex head bit from 4 in one screwdriver or 1/4 inch nut driver. Heating element comes out, take off wire clamps and install new piece. Put screws back in, turn breaker on and that's it!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Buffalo, NY
- Parts Used:
- WB31K10266
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replace a drip pan
OK, I put the drip pan under the burner. Without a single problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rita from LOCUST, NC
- Parts Used:
- WB30X46987
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Oven element broke
Removed bolts unplugged unit then plugged new unit in. Put bolts in and unit works great.
Was this instruction helpful to you?
Thank you for voting!