RB525DD2CC Hotpoint Range - Instructions

The person I spoke to knew exactly what I was trying to describe. The part arrived in 2 days. 5 minutes later the drawer was back in place. I was glad I save the screw as the part did not come with one.

easy, less then 15 min. but take off door first makes alot easier. and don't forget to unplug, like i did. just a few sparks but no damage thank god.

After not using our oven all summer a mouse had been hiding out in the oven insulation and apparenting was starting to make a home. We caught the mouse, but when we turned on the oven recently we noticed a horrific smell and immediately turned it off. It was evident that the smell was not burnt food. We jumped on the internet to see where and how to access the insulation in our oven and found Parts Select. That is when we saw that this is actually a common problem when an oven is not used for a prolonged period. Ordered the new insulation part for our oven and paid extra to have it delivered more quickly. Pulled out the oven from the wall and unplugged it. Took off the top of oven and removed old insulation. Yuck, that was disgusting. Cleaned the inside surface with disinfectant before putting in the new insulation. Took about 20 minutes from beginning to finish.

Moved stove out away from wall .Unplugged stove, turned gas off. Unit is a dual fuel convection. Burners are gas, oven is electric. Removed 4 screws from back shield and exposed the 2 electrical leads connected to broiler element. Disconnected the electrical .Inside oven I removed the front bracket holding element in place, then removed the 2 1/4 screws in the back holding element in place. placed new element in and finger tightened the 2 screws, next I installed the front bracket and finger tightened those. I then snugged the rear screws in followed by the front. I went to the back and reconnected the 2 electrical leads. Replaced back shield and plugged unit in and turned gas back on.Caution; Make sure your gas line is flexible before moving your stove out to far. Repair was very easy

Turn off power to oven. Removed the rack. used a 1/4" nut driver and removed the two screws holding the element to back of oven. Slid the element out, unhook the two wires clipped to the end of the element. Replaced it with the new element, installing it in reverse. Took about 15 min. Rememer to turn off power to oven before attempting to work on it.

Removed old socket, I had replaced with a aftermarket that really did not work well. When I recieved the terminal block kit from your company it was the proper kit. Service was better than expected, part and price was great and it took very little time ti install. Thank you.

My oven is wired into the wall so I had to cut the power off at the fuse box. The hardest part was pulling the stove/oven away from the wall to see if it was a simple plug in or wired in. I lifted bottom drawer out so I could get leverage and lifted the entire unit so I could put the front feet on the soft pads. It slid away from the wall easily. I found a socket that fit the screws on the plate holding the broken element and unscrewed it, saving the screws. A gently tug on the element pulled the attached ends through the hole. The tip of the ends were attached to the wall wiring by a small sliding metal clip. I carefully pulled the ends apart. One was hard to get apart to I had to push it with the tip of a knife. Once the old was off the new was super easy to put back on. Side the tips to the clips, screw the plate in place and push the oven back in place. Flip your fuses and turn on the oven. Yeah!

The repair was somewhat easy. The replacement elements are pushon type. The only thing is that the G.E. Hotpoint wire on the right side of the bake element is short. Be extra careful to not have it go back into the back oven wall or you will have to take the back cover plate (Pull out the range, remove the back cover using a nut driver or a magnetic tip srewdriver with the bit removed works[Wires are right there]. This is as easy a job as can be.

attached the element,pushed it back in the pocket,put the plate back on, screwed the nut and bolt back on and was done in less than 4 minutes!!

I watched the video on this website and it couldn't have been easier. The only thing I did differently was I took the door off for an easier reach. To take the door off, you open just a little and pull up. It makes it so much easier to get at the screws, and maked the repair a snap.

took 5 minutes with a nut driver and son. I had previously watch your video and went exactly as the video described and showed.

ordered part shut electricity off took out 2 screws took of connectors put in new element replaced connectors replaced screws turn on elec started cooking

Remove lower drawer and contents. Unplug unit. Tilt range on its back for easy access. Tie open oven door to forward legs with sturdy rope. Use small socket to remove 2 back screws and 2 forward element hanger screws. Detach broiler element connections from wire clips(2). Insert new element, attach 2 new connections to clips first. Install back socket screws. Install front socket screws for element hanger. Slide in oven shelves. Release oven door rope. Lift range to normal position. Replace lower drawer. Plug 220 in. Test oven element then broiler.

Removed element with 1/4 " nut driver, unhooked element,started to install new element and discovered the wires were too short and had to remove cover on the back to replace wires on the new element. The wires on my range were not as long as the ones showed on the video.It was still an easy repair and the delivery time was less than 2 days. excellent service. Thanks

First and foremost this website was very easy to locate the part number that we needed. Unplugged range from the wall. Removed the upper metal plate off of the back. Removed the ovens' control knob in the front, then removed the 2 screws that released the thermostat. Opened oven door and released the metal thermostat probe. Cut the other end of that wire at the thermostat switch in the rear of the range. Taped that wire to the new metal probe. pulled the old probe out the front of the oven pulling the new probe in place. Switched 1 wire at a time from the old thermostat to the new one in the back of the range. Works great. No more burnt muffins !