RGB518PCH1CT Hotpoint Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Tamyra from Friendship, WI
- Parts Used:
- WB16K10026
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Stove burners no longer working
Ordered 4 new burners, snapped the old ones out, put the new ones in and my stove works great. Also, I got my parts in 1 day. Very satisfied with my experience with PartSelect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charmaine M from York, PA
- Parts Used:
- WB16K10026
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
right side burns would not light, if they did it wrapped around outside of burner unit
Pulled old burners out, cleaned area, sat new units in place, made sure they were stable(no rocking), put the top down on the stove and all burners light like new!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Greg from Ft. Washington, PA
- Parts Used:
- WB02K10254
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
needed to unstall "anti tilt" bracket on back of electric range to be code compliant for property..
Turned off circuit breaker, Then pulled out range, straight out and away from wall and cabinets. Layed braket on flooring and moved stove back in to make certain it aligned with range rear stands. Moved range back out, marked holes in braket, screwed in screws to anchor bracket. Pushed range back into placed against wall. Tried to |"tilt" range by pulling down on door after opened - range was held in place sre
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Willie from Selma, AL
- Parts Used:
- WB35X29720
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
The oven door gasket was worn and didn't provide a good seal.
I use needle nose pliers to remove the old gasket tabs and clean the area with a scouring pad. Then I just lined the gasket up with the holes on the door and pushed the holding tab into the holds.Very easy and simple job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gracie from New Orleans, LA
- Parts Used:
- WB16K10026
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Burners on a gas stove did not work
Ordering from Part Select was very easy. I simply put in the model number of the stove and the replacement needed popped up and explained why I might need this part. Got a professional install because I was not at the location where the repair was needed. Will use Part Select again. The ordering experience was great and delivery was quick and easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Arthur from Oakland Gardens, NY
- Parts Used:
- WB03K10216
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broke a knob on my oven
All I had to do was put the new knob on. No tools were required
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from Redondo Beach, CA
- Parts Used:
- WB35X37973
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench set
My oven bottom got rusty
I removed two bolts at the rear of the oven bottom. I pulled the old oven bottom out, and put the new oven bottom in. I put the two bolts back in and voila it looks like a new oven. Done in less than 15 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ruth from Somerset, NJ
- Parts Used:
- WB35X37973
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Oven liner melted....needed to replace bottom
Removed the old oven bottom by removing two nuts. Be careful...don't drop the nuts! Removed the heat shield that was attached with four nuts to the old bottom and transferred it to the new oven bottom. Then placed the new bottom in the oven and secured it with the two original nuts. Easy...but don't forget about transferring the heat shield and don't lose the nuts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jenny from Muskego, WI
- Parts Used:
- WB35X29720
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Replace oven gasket
I used the pliers to remove the old pins, and popped then new pins in place...super simple!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joan from Watervliet, NY
- Parts Used:
- WB35X37973
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Forgot to remove the heat shield from the old part.
Husband actually did the repair, It went really well except he forgot to remove the heat shield from the old part to attach to the new bottom. (His mistake!)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alice from Valatie, NY
- Parts Used:
- WB35X29720
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
piece out of the oven gasket. Old and brittle.
Remover the old gasket and replaced it with the new. The small prongs I removed with pliers. Need to make sure that the new gasket isn't twisted when you put it on.
Was this instruction helpful to you?
Thank you for voting!