RGB525DEH2BB Hotpoint Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Doan from Flushing, NY
- Parts Used:
- WB16K10026
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
burner did not light
just lift the cover and put it on.less than 1 minute.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carlos from Miami, FL
- Parts Used:
- WB16K10026
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Cracks in the bruner due to corrosion
I bought a new Doble Burner assembly and replaced the old ones.
Piece of cake.
Piece of cake.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Hyojin from Monmouth Junction, NJ
- Parts Used:
- WB16K10026
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The pipe that carry the gas to the ignition part was damaged, therefore the burner was not lightening up.
Just have to remove the old kit and replace it with the new one. No tool required.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- clare from north brunswick, NJ
- Parts Used:
- WB16K10026
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
old burner assembly could no longer be cleaned
pop up range top. pull off old burner. put on new one.
close top. check for rocking. install leveling washer. check again. 2nd burner didn't require leveling so it was quicker.
close top. check for rocking. install leveling washer. check again. 2nd burner didn't require leveling so it was quicker.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Warwick, RI
- Parts Used:
- WB16K10026
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken part
The key here was that I found the correcd part for an older kenmore oven and it was easily installed
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brenda from Franklin, NC
- Parts Used:
- WB16K10026
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
one of the stove top burners had burned all the way through
matched part needed on web site; took off burner; ordered part; received it on the third day and easily replaced it. Wonderful, easy, and very short delivery time! Thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alphonse from Glendale, AZ
- Parts Used:
- WB16K10026
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
We had to buy two dubble burner assemblies because one burner was out on each old assembley
The burner assembly was for my wifes daughter. She raised the top of the stove removed the old burners and set the new ones in place she also used the set washer and it works just fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Forestville, CA
- Parts Used:
- WB16K10026
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The double burner assembly had years of gunk so the burn was not clean.
The old double burners lifted off. Before the new burner could be set down into place, the area had to be completely cleaned using a flat blade screwdriver and damp rag. This allowed the new burners to seat properly in place. That is it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judy from Payson, AZ
- Parts Used:
- WB16K10026
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burners were not burning properly
Just removed the old and set in the new. Waalaa. All is well now. The web site, ordering, shipping and all was super easy.
Thank you
Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- albert from La Veta, CO
- Parts Used:
- WB16K10026
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Back burner not working
Lift stove top, rest it on the pop out holders on stove.
Take old double burner out, Make sure gas port is not plugged.
Put new burner in its place. Make sure it is solid, if not use the washers sent with new burner. turn on gas to burner, to see if it works. Close stove top an wa la!
The bride is happy.;-]
Take old double burner out, Make sure gas port is not plugged.
Put new burner in its place. Make sure it is solid, if not use the washers sent with new burner. turn on gas to burner, to see if it works. Close stove top an wa la!
The bride is happy.;-]
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- PAUL R. from BOSTON, MA
- Parts Used:
- WB18X26988
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Surface burner not igniting
I ordered the part I needed I recirived it overnite by 9 am.
I installed it in 20 min iwould have taken 5 min but the part was of such high quality I had to use a drill to make the opening slightly larger, very easy.the part I received was twice the quality of the original part. Thank You
I installed it in 20 min iwould have taken 5 min but the part was of such high quality I had to use a drill to make the opening slightly larger, very easy.the part I received was twice the quality of the original part. Thank You
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Greg from Ft. Washington, PA
- Parts Used:
- WB02K10254
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
needed to unstall "anti tilt" bracket on back of electric range to be code compliant for property..
Turned off circuit breaker, Then pulled out range, straight out and away from wall and cabinets. Layed braket on flooring and moved stove back in to make certain it aligned with range rear stands. Moved range back out, marked holes in braket, screwed in screws to anchor bracket. Pushed range back into placed against wall. Tried to |"tilt" range by pulling down on door after opened - range was held in place sre
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jenny from Muskego, WI
- Parts Used:
- WB35X29720
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Replace oven gasket
I used the pliers to remove the old pins, and popped then new pins in place...super simple!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Arthur from Oakland Gardens, NY
- Parts Used:
- WB03K10216
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broke a knob on my oven
All I had to do was put the new knob on. No tools were required
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia A from Newport, NH
- Parts Used:
- WB16K10026
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
gas flame flared and blackened pots; gas jets clogged
raised the range top so the supports locked in place. carefully lifted off the old burner assemblies. used a paper towel to remove any black soot from gas jets. opened the plastic package of the new burner assemblies, pulled out the new parts and carefully put them in place. turned on the flame to test... took less than 5 minutes to fix a problem that's been annoying for 3 years!!
Was this instruction helpful to you?
Thank you for voting!