RB636*01 Hotpoint Range - Instructions

The very first thing we did was turned the circuit breaker off and unplugged the range.
My husband removed the back panel and unplugged the switch. Drew a diaghram of the color coded wires. When we received the new one he broke the extension bar off to fit the knob, plugged it in and we were back in business. It was very easy for my husband as he is a mechanic (millwright). However, if you are mechanically inclined it is an easy fix.

I looked for a new terminal locally, but no one had s terminal that would fit a 40-year old range. I went on line to PartSelect and could not find my model range, so I looked through all the terminals listed on the website (about 500) but found only one that was close to mine. Mounting holes did not match, but it had 3 connectors with 220 capability, so I ordered it. I requested express shipping by UPS and thought I paid for the extra charge. When I got notification of shipment. I saw it was via ground. It went from Louisville to Jacksonville to Clearwater, FL. I ordered it on Thursday night and received it the following Tuesday night. Meanwhile, we had no stove to cook on. When the part came, it took two days to get the contractor back to our condo. He drilled new holes on the mounting box and jerry-rigged the wiring to make it fit. The range is now working, but I was disappointed in the delay in shipping which I agreed to express shipping.

The terminal blocks become brittle and carbonized with age resulting in very poor contact with the electric burners. The burners lose capacity to heat fully and eventually stop working.

Unplug the stove first! There is a risk of dangerous electrical shock if the power is not disconnected.

Repair involves removing the burner and the drip cup to expose the terminal block. Remove one screw on top to detach the block from the stove top. Remove the insulating cover and the clip that holds it in place on the back of the block. Detatch the two wires. At this point the age and brittleness of the blocks became apparent as they crumbled in my hand while removing the terminal screws. One screw had several layers of carbonization covering it and required needle nose pliers to get a firm grip in order to loosen it.

Inspect the wires to make sure there are no holes or cracks in the insulation.

Attach the wires to the new terminal block using the new screws provided. The new kit also included quick lock screw fastener clips to place over the holes in the stove top. It's a good idea to use these for more secure mounting and better grounding. Place the new terminal block under the stove top and mount it with the new screw provided. I had to unbend the mounting clip slightly to get it to fit, but it was easy enough to do with bare fingers.

Replace the drip pan and the burner. Plug the stove back in.

A pot of water now boils in under a minute compared to the 5 to 10 minutes it used to take.

popped the new one on!

I followed the easy instructions and everything went well. I had the new switch installed in about 30 minutes. My wires were different colors than on the instructions but it was still easy to figure out where the wires went on the new switch. Just do not be in a hurry and make sure you measure before you break off the extension bar. My knob fit on the new switch without any of the parts that came with the switch.

Unplugged oven from mains.

Removed screw holding terminal block to oven top. Used screwdriver to remove clip holding protective card to terminal block. Removed Philips screws holding wires onto terminal block.

Replacing the terminal block was just doing the above instructions in reverse. The only thing different was to put the speed clip on the range top before attaching the block to the range top.

Removed old terminal block by removing one mounting screw. Removed two wires from block. Installed new terminal block by reversing procedure.

I removed the burner, then the chrome dish. The nuts for the wires were rusted to the terminals, so I had to break the module apart and grind the nuts off.After that the new module went fine.

Your "virtual repairman" was fantastic. I would have purchased the wrong part without trhe diagnostic service. It said that 53% of the time the infinite switch was the problem. In my case it was 100%. Why I put up with this problem for 6 years I will never know.

Repair job was easy but longer than the 15 minutes that it said it would take.

First of all I did this repair because the wire to the burner shorted out. I did the wire portion first - only then did I know I needed the switch kit. (The burner was operating while my old swithch was OFF). The first (wire replacement) repair took about 10 minutes - I followed the guidance on this web-site. The second repair (The switch) took about 20 minutes. The switch ws not the same as the original. Just be careful to mark each wire as you remove them from the old switch's posts. The posts on the switch are marked and you need to place them on the like-marked corresponding posts on the new switch. All is well, my burner is operational.

1. The infinite switch had several knobs which would fit the switch shaft. Read the directions included with the switch in order to have the shaft fit the proper knob. You can break the shaft with two pairs of pliers. 2. Move the stove away from the wall and unplug it. 3. Remove the 1/4 screws from the back side of the stove and remove the back panel, exposing the switch. 4. Remove the wires one at a time and put them on the new switch. The terminals are L1, L2, P, H1 & H2. The Pilot (p) has a smaller terminal so you don't get it mixed up. Generally L1 is black, L1 is red, P is yellow, H1 and H2 can be blue, brown, yellow, orange or one of these colors striped on a white wire. 5. Remove the old switch from the stove and be sure to save the two mounting screws. 6. Position the new switch so that the side of the switch marked "top" is on top. 7. Install the screws on the new switch and put the knob on it. 8. Carefully test the burner. 9. Unplug the stove and put the back cover on.

Replaced drip bowls.

The only hard part of the job is removing the old, corroded terminal block. Be careful not to break the electrical wire. Other than that, just sand the contacts and reassemble. This is the second one I have replace on my 4 burner stove. 2 more to go.

I located and removed 2 sets of hex-head screws under the front lip of the cooktop, then lifted the entire cooktop to access the burner controls. Removed the wires and taped them, and took out the old control after removing 2 phillips head screws. Installed replacement part easily. Only tricky part is that the various shaft adapters don't quite work with my knob. I'll fix it completely with a bit of epoxy and the adapters they sent.

I turned off the circut breaker and disconnected the old terminal block - some difficulty removing the wires because of corrsion - I was able to reconnect the wires to the new block quickly and I was done - fast and easy - so happy to have found the part so easily with your program. Thank you