RS47G*04 Hotpoint Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Fernando from Auburn, GA
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Burned out oven element
Remove two screws that secure the plate to the oven wall. Pull element out about 6 inches, then remove two screws that attach the element to power lines. Reverse for installation. Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- pierre from virginia Beach, VA
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench set
Electric Burner In oven failed
Parts arrived quickly and install was easy as removing two screws and removing the broken burner. Installed the new and I was done!
Was this instruction helpful to you?
Thank you for voting!
Old and corrosive due to age
After receiving parts, was getting rims unpackaged and removing the old rims, then and installing the new ones. Extremely easy to do. No tools needed
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Courtney from Coon Rapids, IA
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Blown Baking Element
The old part was easily removed with a nut driver, and the new element went right in with a nut driver and screwdriver.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from Bartlett, IL
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
heating element split
I was able to slide the stove out from the wall, so it was easier to remove the back cover and disconnect the wiring in back rather than trying to reach into the oven. Then all I had to do was put in the new coil, reconnect the wires and slide the stove back into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sally from Ravenswood, WV
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Element replaced
It was quite easy-hooked up the wires replaced screws to hold it in place-finished!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Merle from Hainesport, NJ
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Over took forever to come to temperature
My daughter and I turned off the breaker to the range and removed the old element and replaced it with the new one. My husband came home and took over after we had done almost everything ourselves!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sherry from Keller, TX
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Oven heating element burned out
I was very pleased with all the follow up from the time of order until the arrival of the heating element. I have never had the personal communication as I did with your company. The part was ordered on Dec. 26th and arrived on Dec. 29th. Due to the holiday schedule, I did not expect arrival until weeks end. My neighbor installed the heating unit for me and it is doing just fine.
Thank you for the excellent service.
Sherry Shelton
Thank you for the excellent service.
Sherry Shelton
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Naperville, IL
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Oven was uneven in temperature
Removed the bracket holding the element, slid out the element, disconnected it from the leads, replaced it with your part and reassembed. Oven now works like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Teresa from Grand Foks, ND
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
oven element cracked apart, oven would not heat
1-Shut off the breaker
2-Pulled off the oven door for easier access
3-Unscrewed the old element plate
4-Unscrewed the red and black wires from the old element
5-Screwed on the new element to the wires
6-Replaced the screws on the new element plate
7-Turned the power back on
2-Pulled off the oven door for easier access
3-Unscrewed the old element plate
4-Unscrewed the red and black wires from the old element
5-Screwed on the new element to the wires
6-Replaced the screws on the new element plate
7-Turned the power back on
Was this instruction helpful to you?
Thank you for voting!
Old trim rings were rusted and soiled
Too easy to describe. Just lifted out the old rings and popped in the new ones. PartSelect is my go-to source for appliance parts both for my home and my job as maintenance man for residential group homes in my area. Website is easy to use, prices are good, shipping is always surprisingly fast. Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Fairfax, VA
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Cracked Heating Element (lower)
Unplugged oven. Removed the two screws from inside the oven that secured element to the back. I then removed the protective cover for the plug from behind the oven-three screws. Disconnected the element from the electrical wires, removed and replaced the element. And reassembled the cover and all the screws in reverse order. Plugged it in. Presto, 5 mins and works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Melvin from Houghton, MI
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Heating element burned out
Repair was super easy - read the other stories posted. They give more than adequate instruction.
Amazingly helpful website. Found the part, instructions to install, and able to order in less than 20 minutes!
Amazingly helpful website. Found the part, instructions to install, and able to order in less than 20 minutes!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenny from Greenville, MS
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Oven Element would not heat up
I first turn off the 220 power braker to the electric stove. Making sure the stove and element is very cool.
I then removed the two screws that hold the lower baking element in place. Pull gently on the element not to break the wires from the wall of the stove (about 3 to 4 inches).
I than unscrewed the right and left wire attached to the element with the nut driver. (This old element was attached with small nut screws. The new one has screws that use a screw driver). Keeping the wires apart, I removed the old element and replace it with the new element part.
In replacing the new element, facing the stove I connected the black wires to the left side (my left hand) and the white wire to the right side (my right hand) with the new screws using a screw driver. REMEMBER TO REPLACE THE WIRES BACK THE WAY THEY CAME OFF WHEN THE STOVE WAS WORKING PROPERTLY. Attach the element back to the stove and turn the breaker on. Easy to do job.
I then removed the two screws that hold the lower baking element in place. Pull gently on the element not to break the wires from the wall of the stove (about 3 to 4 inches).
I than unscrewed the right and left wire attached to the element with the nut driver. (This old element was attached with small nut screws. The new one has screws that use a screw driver). Keeping the wires apart, I removed the old element and replace it with the new element part.
In replacing the new element, facing the stove I connected the black wires to the left side (my left hand) and the white wire to the right side (my right hand) with the new screws using a screw driver. REMEMBER TO REPLACE THE WIRES BACK THE WAY THEY CAME OFF WHEN THE STOVE WAS WORKING PROPERTLY. Attach the element back to the stove and turn the breaker on. Easy to do job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Elkton, VA
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
bottom element was burnt out
removed 2 screws that hold the element in place, then pulled element out took 2 more screws out and reversed proc. I couldn't have had a better rep to help me find the right part. Thank you
Was this instruction helpful to you?
Thank you for voting!