RGB790DER1WW Hotpoint Range - Instructions

remove screws, re-install screws

Replaced the flat style oven igniter. First, I watched the video on your web site, and used it as a reference to make the repair. I did remove the oven door tho, as it made it easier to complete the work, the video didn't show the door being removed. The video was very helpful.

It was pretty simple. Just remove the door as the bottom piece holds all the parts together. Place on table top and remove old trim. Install new trim and install door. The only difficult part was the trim had a space for the glass door front. I opened up the space so that the glass would seat easier. Went together real easy. Stove looks like it's brand new.

In my case it was the lower burner so I unplugged oven and turned gas off.
Then I removed the bottom drawer, and the lower burner cover.
Next unplug Oven Igniter, found where drawer existed.
Removed 2 screws attaching Igniter using nutdriver
Placed new Igniter on
Plug Igniter in and tested oven
Replace burner cover and drawer


This was much easier then what I went through with a repair man the first time around. These Igniter are designed for certain model stoves and are not interchangable with other model stoves!!!

In general, other repair stories on this site collectively give a good description of the repair process. My words concern the decision that has to be made as to which element is bad - igniter or gas valve. To reach a conclusion about this question, I was comforted by the fact that I could measure the AC electric current through the gas valve which then let me decide that my problem was in the igniter. Since the circuit is a simple series with three elements, thermostat, igniter, and valve and the resistance of the valve unit was 1.0 to 1.2 ohms (per GE range equipment instruction which came with the range) by measuring the AC volts across the valve, I found (by dividing the volts AC across the gas valve (2.3 volts) by the resistance of the valve mechanism (1.0 ohms) that my old igniter was only supplying 2.3 AC amperes (instruction sheet states 2.9 amps. is needed to actuate the valve and further while heating of the oven is occurring the valve AC current will raise to 3.2 to 3.6 amps.). At 2.3 amps. the igniter will glow at a yellow color but will not actuate the valve. When you replace the old igniter with a new one you will enjoy to measure voltage across the gas valve once again and discover that the voltage rises to 2.9 volts and that the gas turns on and the heater tube gas is ignited.

On a 18 year old electric GE range: amazing not the exact handle but it does fit perfectly and looks great. If your somewhat handy this is very easy and can be completed in less than a half hour. Save the screws from the old handle, they can be used again.

Remove the existing burner and install the replacement.

Very simple. Lift oven door off brackets and set on floor. Remove sheet metal screws holding on existing trim piece, Clean area beneath trim.
Put new trim piece on, don't tighten any of the screws until all have been started as some adjustment is needed to align the holes for the screws.

Very was ti replace racks and knobs. Very fast mail service

Unscrewed eight screws. Removed rusted part. Cleaned area with Windex. Replaced new part.

Step 1 pull the broiler completely out of the bottom of the oven. Step 2 unplug the igniter Step 3 remove 3 small screws to pull the burner tube completely out of the oven. Step 4 replace the igniter and repeat steps to install burner tube back into the oven.

replaced lights in refrigirator and freezer

Removed two screws to remove old bottom. Insert new oven bottom and re-attach screws.

First I removed the racks and oven bottom panel. Then I took out the two screws holding the ignighter unplugged the wire connection and removed the old ignighter, compared the old with the new one mounted it back with the two screws plugged it back in. Job finished in 15 minutes and oven back working again.

Removed oven racks, removed lower oven shelf panel by using a flathead screwdriver and removed two screws on the back edge of the panel. Removed flat style ignitor (two hex head screws)from the gas burner tube using a 3/16 nutdriver. Disconnected two wires from the ignitor. Removed the two pin connector from the new ignitor, stripped the insulation to expose about a 1/4 inch of bare wire at the ends of the wire where the connector was removed. Installed the ignitor to the gas burner tube using the 3/16 hexhead screws. Connected the wires using porcelain wire nuts. Re-installed the lower oven shelf panel, flathead screws and the oven racks. Oven worked as advertised.