RB787CH5CC Hotpoint Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Andrea Hines from ELGIN, AZ
- Parts Used:
- WB30T10045
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Heat element died
Very easy to replace. So easy even a man can do it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anil from Milpitas, CA
- Parts Used:
- WB24T10029
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burner spontaneously cycled without knob activation
First I cut the circuit at the breaker, and then pulled the range from wall to access the access panel. This top panel was held with 4 screws and removable with a standard phillips head screwdriver.
I then removed the 5 wire-crimped fasteners from the defective surface burner switch. (I first labeled these wires to ensure correct placement to the new switch). There were an additional two screws behind the corresponding knob that needed to be removed in order to completely remove the old switch.
The new switch was installed in reverse order to the steps indicated above (two screws behind knob, 5 wire-crimped fasteners, 4 screws to panel). Range was pushed back into position and breaker turned on.
I then removed the 5 wire-crimped fasteners from the defective surface burner switch. (I first labeled these wires to ensure correct placement to the new switch). There were an additional two screws behind the corresponding knob that needed to be removed in order to completely remove the old switch.
The new switch was installed in reverse order to the steps indicated above (two screws behind knob, 5 wire-crimped fasteners, 4 screws to panel). Range was pushed back into position and breaker turned on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stella from PADUCAH, KY
- Parts Used:
- WB27X45466, 40A15
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Socket set
My electronic control board went out so I could not use my oven. My oven light blew as well.
I started with changing the bulb. I removed the small bracket that holds the glass cover over the bulb unscrewed the bulb and reversed to replace the bulb. To replace the control board I removed the top plate on the back of my stove took the small screw's out of the control panel and unplugged the wire's. Plugged the wire's into the right spots on the new control board and put it back together.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from SARASOTA, FL
- Parts Used:
- WB30X46987
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
would not heat
Did the repair just like the video shows.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Melvin from WEBSTER, TX
- Parts Used:
- WB27X45466
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
THE FACE PLATE IS HARD TO GET OFF THE OLD CONTROL BOARD. USE A THIN KNIFE
THE INSTRUCTIONS THAT COME IN THE EMAIL ARE VERY GOOD. BE SURE TO TAKE A PICTURE OF THE WIRING.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from DIAMOND SPGS, CA
- Parts Used:
- WB30X46987
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
The lower,BAKE, element had burned in half almost causing a fire.
Slide the rang out to access the 240V plug & unplugging it. Removed the sheetmetal cover from the rear of the range to access the slip on wire plugs to prevent damaging the insulation. The insulation would be damaged if pulling them through the opening in the oven wall with the plugs attached to the element. Removed the racks from the oven. Unscrewed the retaining screws holding the element to the rear wall of the oven, lifted damaged element out and reversed the process for instillation. Perfect opportunity to clean underneath and behind the range.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from PAWTUCKET, RI
- Parts Used:
- WB24T10027
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Top glass top burner wasn’t working
I first ordered the wrong part and had to call customer service. They handled the return and ordered the new piece beautifully!! The installation was really simple. Once I took out two screws holding the top down, I removed three clips holding the burner on then switched out the electrical leads. Put everything back and it worked perfectly!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alex R from Randoff, NJ
- Parts Used:
- WB23X5340
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
temperature sensor went
Took back panel off unplugged sensor and replugged in and worked like a charm!Sears wanted $400 and was going to 'overrepair"Got the 60 dollar part on here. UPS shipped to wrong address and customer service refunded my shipping and was excellent! would definetly use again!thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roscoe G from ROCHESTER, NY
- Parts Used:
- 40A15
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Light burnt out.
Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MICHAEL from MORROW, GA
- Parts Used:
- WB30X46987
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Oven would not heat up
I removed the rear lower cover. Disconnected the terminals from the heating element. Removed 2 screws from the heating element from inside the oven. Removed the heating element. Reinstalled everything in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from ANDOVER, OH
- Parts Used:
- WB04K10021
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Rubber cracked
Took 5 minutes to repair easy peasy??
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from WOOSTER, OH
- Parts Used:
- WB24T10027
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
The burner would not turn off and I or my wife would have to turn the breaker off.
I simply turned the power off and slide the stove forward to give myself room to get behind it and just unscrewed the cover behind the burner switchers and pulled the switch knob off then I removed the two small screws that hold the burner switch to the control panel and go to the back and pull the wires carefully and replace them on the new switch one by one and screw the new switch to the control panel and replace the back panel and done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jackie from TICKFAW, LA
- Parts Used:
- WB27X45466
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Oven board went out
One wire at at time then used my razor blade to get front off stuck right back on
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vincent J Paola, from GREENWEL SPGS, LA
- Parts Used:
- WB27X45466
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Bad Line fault displayed on range clock
1. Unplug the range power cord from the outlet.
2. Moved range away from the wall and countertop.
3.Using a nut driver removed the 2 screws on each side of the removable panel on the back side of the control knobs and clock.
4. Using a phillips head screwdriver remove 2 screws on top side of the back side panel.
5. Using a nut driver remove 4 screws that secure the main control board in place.
6. Take photo of the wiring on the main control board if not color coded.
7. My control board, and the replacement board were both color coded with the color with the wire placement on the rear of the board.
8. Remove wires with needle nose pliers.
9. Using a hair dryer, heat the plastic control panel face plate that fits onto the front of the old control board.
10.With a putty knife carefully pry the face plate from the old control board.
11. Install the control board face plate onto the new control board.
12. Install the color coded wiring in place on the back side of the control board.
13. Replace the control board into the range, and install screws, and rear panel of the range.
14. Plug cord into outlet and test range for proper operation.
2. Moved range away from the wall and countertop.
3.Using a nut driver removed the 2 screws on each side of the removable panel on the back side of the control knobs and clock.
4. Using a phillips head screwdriver remove 2 screws on top side of the back side panel.
5. Using a nut driver remove 4 screws that secure the main control board in place.
6. Take photo of the wiring on the main control board if not color coded.
7. My control board, and the replacement board were both color coded with the color with the wire placement on the rear of the board.
8. Remove wires with needle nose pliers.
9. Using a hair dryer, heat the plastic control panel face plate that fits onto the front of the old control board.
10.With a putty knife carefully pry the face plate from the old control board.
11. Install the control board face plate onto the new control board.
12. Install the color coded wiring in place on the back side of the control board.
13. Replace the control board into the range, and install screws, and rear panel of the range.
14. Plug cord into outlet and test range for proper operation.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Melvin from Portland, TN
- Parts Used:
- WB24T10029
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Element blew hole in self then no power to burner.
Replaced burned element, did not fix no power problem. Ordered receptor replacement, replaced it, took less than 10 mminutes, but still no power to burned. Then ordered replacement switch, replacement too less than 10 minutes again and burner works fine.
Was this instruction helpful to you?
Thank you for voting!