RGB540SEP2SA Hotpoint Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- david from harrisburg, PA
- Parts Used:
- WB20K8
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven Would Not Turn Off
I read the instructions from other peoples repairs. One note: unplug stove, and turn gas off, remember where wires go. I didnt have to remove top of stove completly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff from Geneseo, NY
- Parts Used:
- WB20K8
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Oven would not turn off even though knob was turned off.
Unplugged stove. Removed the top rear panel to see where the thermostat cable fed into the oven. Left the current cable in place and fed new cable along side the old one. Pulled out the old cable once new one was installed. Attached wires to new thermostat and installed. Turned oven on to test. Everything went great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harriet from Jacksonville Beach, FL
- Parts Used:
- WB48T10095
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Open door. Put racks in.
nothing to it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from Ogdensburg, NY
- Parts Used:
- WB16K10055, WB29K10001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Stain/polyurethane dried on burner head & cap
Lifted both pieces off and placed the new ones on,turned on the burner and it worked as it should.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from Brandenburg, KY
- Parts Used:
- WB08T10026
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Oven light wire broken, damaged socket
Remove light bail, glass cover held by two nut screws. Pull socket, removed clips in back, replaced wire connectors, placed new socket in, then glass cover and bail. Wire connected in back, cover plate replaced.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vincent from Aldan, PA
- Parts Used:
- WB35K10042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Old bottom oven was really crusted and way too hard to clean.
Removed oven door.Opened slightly and lifted off.Removed two screws from rear of oven bottom.Lifted out bottom oven.Reversed for installing new bottom. Looks great.And the price was well worthit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anne Marie from Andover, MA
- Parts Used:
- WB48T10095
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old dishwasher rack and silverware rack
The whole process was very easy! I just got the model number and bought a new rack and silverware holder on,one. There was no assembly needed so I just popped them in and replaced the old ones! Very easy to do!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from North Las Vegas, NV
- Parts Used:
- WB16K10070, WB16K10055, WB16T10046
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
carbonized burners
Replaced all four
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Los Angeles, CA
- Parts Used:
- WB16K10055
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burner would not ignite.
Could not have been simpler. Burner head dropped into place and was held in place by gravity. Not possible for part to go in incorrectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rebecca from Las Vegas, NV
- Parts Used:
- WB27T10469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
no display
Turned off circuit breaker to stove, remove top panel and then the old control module and installed replacement. Power back on and top panel reinstalled. Easy!!! And Everything works like new!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kate from San Francisco, CA
- Parts Used:
- WB03K10037
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
housecleaners had scrubbed off the majority of thermostat numbers
took off the old one; put on the new one! easy-peasy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leo from Roseville, MI
- Parts Used:
- WB28K10190, WB28K10189
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
open cook top / tubs pulled out front of stove
unplug power and turn off gas/// had to remove all star screws on top/remove ign wire from each burnner/now remove stove top/ adj wrench and remove nuts from the front nobs and relace with new front orifice tubes NOTE: Front orifice tube is the leftside. Front orifice HOLDER is the right side. put back top, open front to put hand in to make adjustments to ign wires close top and reinstall star screws and using finger to hold and make adjustments on top now turn power and gas on. I use soapwater to test for leaks/ leo gubin
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Monterey, TN
- Parts Used:
- WB08T10026
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
broken light socket
The only tool needed was a nutdriver to remove the lamp socket. I needed my head mounted light to see what I was doing, and everything went smoothly from there. Simple job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janet from Jessup, PA
- Parts Used:
- WB28K10190, WB28K10189
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set, Wrench (Adjustable)
Bent/Broken Front Orifice Tubes
I removed the two nuts that secure the rear orifice tubes. This allowed me to lift the range top to access the broken tubes. Once lifted I removed the nuts that held the broken orifice tubes. I then connected the new orifice tubes. I removed the three(star)screws that fasten the orifice brackets under the range top. Doing this allowed me to connect the new tubes without having to maneuver them at all. I then lowered the top just enough to reattach the brackets. After securing the rear tubes I snapped the range top back into place. Just remember, if you use propane for cooking then you must remove the brass orifices from the old tubes and place them in the new ones. If you don't do this then your flame will not burn properly. Simply unscrew them from the old tubing and put them in the new tubing.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Alameda, CA
- Parts Used:
- WB20K8
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
With the oven dial at OFF, the oven would turn on by itself every 5 to 10 minutes and it would heat up to about 100F and shut off.
Unplugged the range. Took out all the necessary screws and lifted up the cooktop cover. Unscrewed each gas tubes connecting to each gas burner's dial to allow more working space. Pulled out the old thermostat, installed the new one. Put back the gas tubes and all other necessary screws. Plugged the range and tested out the new thermostat.
Was this instruction helpful to you?
Thank you for voting!