RB734*J1 Hotpoint Range - Instructions

We just took out the old one and put in the new. Works great!!

DISCONNECT POWER !!!! Removed 2 screws to get element loose from rear wall of oven and 2 srews to remove wires. Reverse for installation. The replacement part fit perfectly and works just fine.

Removed old element by unbolting two nuts, replaced with new element and two new nuts that were included. Very easy and worked fine.Wish all repair jobs were this easy!Great service with ordering and prompt delivery, too.

Took out the two screws that held the old element. Disconnected (unscrewed) the two power cords. Screwed in new power cords and put two screws in new element. Works like a charm. Took longer to get the new element out of the box than to replace it! Thank you!!!

Wasn't sure what to do had a friend come over and it was fixed in less than 15 min. The shipment was really fast and although I only had a partial model number because of age of the unit your search engine found it. Thanks all, my wife is very happy. Your the best!

Shut electric off to range[circuit breaker], removed door and baking racks, removed two screws holding element to back of the oven compartment, pulled the element out to expose the wires, removed screws fastening the wires to the element. Discarded the damaged element and installed the new one in the reverse order. Turned on power and tested. Everything worked fine.

Unplugged oven. Removed the two screws from inside the oven that secured element to the back. I then removed the protective cover for the plug from behind the oven-three screws. Disconnected the element from the electrical wires, removed and replaced the element. And reassembled the cover and all the screws in reverse order. Plugged it in. Presto, 5 mins and works great.

CAUTION: Make sure stove is unplugged as there is still current with it off! Removed 2 screws to pull old element out & 2 screws on electrical wires. Put new element in & screwed all screws, very easy repair. A big THANK-YOU to PartSelect for getting the part to us so fast!!

Followed directions left by a previous user on PartSelect: 1. open oven door and lifted it off hinges; 2. Unscrewed mounting element mounting plate from rear of oven (may need nutdriver, allen wrench or screwdriver) 3. Unscrewed electrical leads from element; replaced with new element and reversed the steps.

First we unplugged stove, if wired into circuit shut off in breaker box. Undo four screws on back cover and detach wires from element. Remove oven door by pulling open and sliding it up off hinges. Undo two screws holding element to back wall of oven. Slide in new element and replace screws in back wall. Replace door. Slide wire leads on new element in back, at this point we plugged range in and tested element to see if heating. It worked so we replaced cover, slide range in and leveled it with wedges. Time for pizza.

The repair is simple. Unplug or turn off power to stove. Remove the 2 visible screw where the element connects to the back of the oven. Pull the element with back plate out. The back plate is part of the element. Remove 2 screws that connect wire. Mark which color connects to which lead. Re-assemble in reverse order. Takes about 15 minutes,

fairly easy. Only four screws. The only problem was reaching the back of the oven without hurting my back and being careful not to over tighten the wires to the new burner ends. I wish all repair were as easy.

1st. turned breaker to oven to off position. removed oven racks from oven. removed "2" small metal screws that held baking element in place to back of oven. easily pulled element toward front of oven. removed two additional metal screws that connected "element" to oven wiring. connected new element to wiring using screws, pushed back in place to back of oven, and replaced screws that held baking element in place. replaced oven racks and turned breaker to on position. total time apprx. 7-8 minutes.

I have some electrical experience. It was simple to remove and install. You just have to pay attention to wiring upon removal and installation.

Removed bolts from fixing plate, pulled out existing element, unscrewed wire connectors and installed new element in reverse order of removal. This is an old stove from the 60's or 70's so I was glad to get a replacement part and fit it myself so easily.