RB787BB1BB Hotpoint Range - Instructions

Moved the range out and disconnected the power cord. Removed the back cover.Disconnected wires after labeling the them. Removed the unit from the range,Carefully removed the front decal and applied to the new unit. Installed the new unit into range and wired according to the instruction and put the covers back on. plugged back in and tested the range and everything functioned correctly.

The part was just like the old one and would have been an easy fix except our range suffered from a lighting hit. The clips had melted together. Called a dealer and asked about a new wiring harness. He said in those cases just cut the clip off and hard wire with wire clips,or firecrackers. We used wire nuts and taped all together and the oven works just great. Nothing is ever as easy as it should be.

Good directions

The original controls were different for the small burners and the large burners. The replacement part fits all. Before removing wires, pay attention to writing on new and old control and replace 1 at a time. The hardest part was being sure to cut the knob stem to the correct length. Control works well.

After needlessly replacing the Thermo-sensor and Bake element I was able to determine that, while I had proper voltage to the appliance I did not have power to bake element when bake knob was turned on. The broil element worked properly. I hesitated purchasing the Electronic Clock Control because there was nothing wrong with the oven clock and it was an expensive part. I switched out the control unit and was delighted to see the bake element heat up immediately. It was simple to replace and the instructions that came with it were adequate - just some differences in the color of wires. Thank you Part Select.com!

The repair went very smooth and easy it took me around 10 minutes to replace part and I was ready to bake again

I took a chance and guessed that the problem was the element, as opposed to a thermostat or other part that may have failed. (Oven was made in the 70's) I entered the data for this old oven on the PartSelect.com website and it came up with a part for me to order. When I received the replacement element, I noticed that it was not "exactly" the same shape as the old part, but the dimensions were correct and it fit into the space on the bottom of the oven without any problems. The dimensions of the connectors were pretty close to exactly the same as the old element, and the screw holes in the mounting plate lined up perfectly with the corresponding threaded holes in the back wall of the oven - it took me less than 15 minutes to install the part and the oven appears to be working perfectly again.

Removed two screws, pulled old element forward 2 inches, removed two wires. Pulled old element out of oven. Put new element in oven, attached two wires, pushed element all the way in, put two screws in and tightened them. Turned oven on to test new element. Element worked. Project completed.

It took longer to get the new element out of the box than it did to install it. I removed the two screws with a 1/4" nutdriver, pulled the element out roughly three inches, unplugged the connectors and discarded the old element. I did the reverse to install the new element.

took the two screws out that hold it in. gave it a tug ,pulled it through the insulation and pulled the plugs off replaced with new element screwed it back on and good to go. simple if you can handle a screw driver you can do this with a skirt on :)

Remove light bail, glass cover held by two nut screws. Pull socket, removed clips in back, replaced wire connectors, placed new socket in, then glass cover and bail. Wire connected in back, cover plate replaced.

replaced bake elementAndrew W. was helpful getting the right part..

Removed old; inserted new.

already had the old one disconnected (spade ends) on old element, new one arrived installed it the same way I removed the old part, just 2 little screws to hold it in place, after you reconnect the spade ends. Then plugged the unit back in. Always use common sense when working with electrical appliances! Easy as the pie I can now bake.

replacement was easy. pulled away the stove from wall. unplug the stove. open oven door. remove the two hex head screws holdings stove top. raise the stove top in the front. supported stove top with a 16 inch piece of wood. place New Burner under old burner. remove old burner remove wires remove old burner and place it on top of new burner connected the wires from burner to new burner. install new burner. remove support lowered top down. plugged in stove tested. .burner. burner w.ork fine. reinstall hex head screws back top. pushback stove back into the wall. testes over again. all the stove work done.