RB753BB1 Hotpoint Range - Instructions

Of course the first thing is to turn off the breaker, Unplug the appliance, pull the two electric feed wires off the old element. Then remove the four screws that hold the fan guard in, After that the two screws that held the Bake Element in place. Then reverse the process to install the New Element. Took about twenty mins. from start to finish. Just Like New. And thanks to Parts Select for their prompt service, Had the new part in two business days.

It was so simple looking, I had it shipped to the tenants of the house. They swapped it out easily, and were happy to get back to baking.

First I shut off the power at the power box. Second I removed two screws in metal plate. Third I unplugged the two wires. Repeated steps backwards and it works great.

No repair needed, element fitted right in.

saw when heating the stove up the bottom element wasn't getting hot. got part number and looked up online and ordered

Your "virtual repairman" was fantastic. I would have purchased the wrong part without trhe diagnostic service. It said that 53% of the time the infinite switch was the problem. In my case it was 100%. Why I put up with this problem for 6 years I will never know.

Repair job was easy but longer than the 15 minutes that it said it would take.

First of all I did this repair because the wire to the burner shorted out. I did the wire portion first - only then did I know I needed the switch kit. (The burner was operating while my old swithch was OFF). The first (wire replacement) repair took about 10 minutes - I followed the guidance on this web-site. The second repair (The switch) took about 20 minutes. The switch ws not the same as the original. Just be careful to mark each wire as you remove them from the old switch's posts. The posts on the switch are marked and you need to place them on the like-marked corresponding posts on the new switch. All is well, my burner is operational.

I ordered it on line and it was easy to fix, I had it done before my husband came home from work. I just undid the old one and pushed the new one on. I have to stay ordering from here was alot cheapier

I located and removed 2 sets of hex-head screws under the front lip of the cooktop, then lifted the entire cooktop to access the burner controls. Removed the wires and taped them, and took out the old control after removing 2 phillips head screws. Installed replacement part easily. Only tricky part is that the various shaft adapters don't quite work with my knob. I'll fix it completely with a bit of epoxy and the adapters they sent.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and unscrewed the the two screws that connected the wires and element together. I then tried to connect the new element to the wires, but found that the screw holes were smaller than the original holes in the old element and the original screws wouldn't fit. No problem, I then got a cordless drill and found a drill bit a little bigger than the holes, I held the element connector with pliers and made the screw hole a little bigger, same with the other connector. I screwed the screws into the connectors with a socket wrench and then screwed the element back into the holes in the oven, then turned on the oven and it works as good as new.

My Husband did the repair. It took him longer to prepare the appliance than it did to perform the actual replacement of the bake element! We LOVE the service and the selection found at PartSelect!! Our part arrived within 24 hours!We've recommended you to all our friends and co-workers. Bravo! Thank you again.

Removed the cover plate, pulled the element out, removed the screws holding the wires in place, but then I had to enlarge the screw holes on the new element in order to fit the screws into the new element. Took a while with an awl to enlarge ther two holes. Connected the new element, pushed it back in and replaced the cover plate. Worked great.

Removed both racks, removed two screws holding element in. Removed two screws holding wires on element. Drilled holes in new element where the push-on connectors are attached so I could attach the oven wires to the new element. Attached the wires and screwed the element to the oven. Fit perfectly and the temperature of the oven matches the control knob finally!

Thanks.

1. The infinite switch had several knobs which would fit the switch shaft. Read the directions included with the switch in order to have the shaft fit the proper knob. You can break the shaft with two pairs of pliers. 2. Move the stove away from the wall and unplug it. 3. Remove the 1/4 screws from the back side of the stove and remove the back panel, exposing the switch. 4. Remove the wires one at a time and put them on the new switch. The terminals are L1, L2, P, H1 & H2. The Pilot (p) has a smaller terminal so you don't get it mixed up. Generally L1 is black, L1 is red, P is yellow, H1 and H2 can be blue, brown, yellow, orange or one of these colors striped on a white wire. 5. Remove the old switch from the stove and be sure to save the two mounting screws. 6. Position the new switch so that the side of the switch marked "top" is on top. 7. Install the screws on the new switch and put the knob on it. 8. Carefully test the burner. 9. Unplug the stove and put the back cover on.

I ordered to correct part from PartSelect with relative ease given I know nothing about oven repair. What's even more amazing, my wife who is not mechanically-minded, took the element home and replaced the broken one in 15 minutes with nothing but a pair of pliers. We live 22 miles from town so a repairman would have cost over $100 just to show up. Total cost = $36!