RGB535BEA2WH Hotpoint Range - Instructions

replaced lights in refrigirator and freezer

The grates are slightly smaller then the original Kenmore parts and they slide slightly. I purchased a full set of 4 grates - part number PS244182

parts need to be delivered to do repair, its been over a month. customer service is not taking calls. I have paid for parts I did not receive.

No longer carry the one to our stove so it was substituted with Nafisa on it. You could see all the electronics so we had to pry the old face off the old one blew it in place, but a clock was reversed from timer, but it works.

I put it in the same way tuck it out

This gas range had an oven that would heat, but it wouldn't hold it at a stable temperature. Say you set it at 300 degrees. Well, it'd head up to broiling temperatures, then drop down to like 200 degrees, then 400 degrees (You get the picture).

My guess was that the thermostat, given that this oven was ~20+ years old, was no longer able to detect correctly the temperature inside the oven.

The thermostat sensor is made up of the housing (The part that sits behind the oven temperature control knob), a long wire (so you can route it to the inside of the oven), and the probe itself (Which I boldly assume is the thing that measures the temperature inside the oven)

TL;DR:

-Pull oven from wall.
-Turn off electric and gas.
-Remove the grates and drip pans off the top.
-Pry the range's cooktop up (It's on like a hinge and is designed to lift up. You have to play with it a bit with like a screwdriver on the sides (One on each side). If you pry just a tad, you'll notice these prongs that act like detents. (LIFT CAREFULLY, the heating elements are still connected via their gas lines! They're flexible, but don't man handle the thing!
-Once that's up, it's time to finally start removing the thermostat which is the knob that controls the oven temperature. Pull the plastic knob off which will expose the two screws you need to detach it from the oven (Phillips head). Be super careful. You don't want to drop these screws. You'll be struggling to fish them out of the empty space that sits between the thermostat and plastic knob.
-Once that's loose, open the oven door and detach the thermostat from the back of the oven. Recycle the prongs holding the old thermostat sensor for the new one.
-Go to the back of the range. Like the actual back part of it.
-Frustrate yourself with pulling out the thermostat through the route it's been put in. It's difficult to route it through the tight spaces, but not complicated. Keep a mental note of this route and copy it with the new thermostat that you have to install.
-Don't fret, when it comes time to wire the new thermostat sensor, it's actually a lot easier than you would think to find that little hole in the back of the range that you have to slot it through. It's just slightly covered by insulation. Pulling it slightly aside, you'll see it very easily.
-Screw in the thermostat housing at the front of the oven.
-Frustrate yourself again by routing the wire while taking care not to bend the probe (This is my assumption not to bend it and I think it's a safe assumption to make)
-Find that tiny little hold in the back of the range again, insert the probe through it, then use those recycled prongs to hook that probe into place.
-Yay, you're almost done.
-Reinsert knob on thermostat.
-Turn gas and electricity back on.
-Give it a test run to see if you did it right.
-if it still doesn't work, then it might not have been the thermostat giving you problems.
-If it does work, put everything back the way it was.
-You're done.

Followed you tube instructions I found on line via parts select recommendations.

remove grates and ceramic discs replace old pans with new ones. looks as good as new.

Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.

My husband and I probably could have done the repair in 15 minutes except for the difficulty lifting up the range top, dropping the screws into the range where they could not be retreived, threading the thermostate into the little holes from the top to the inside of the oven and then trying to hook the range top back into place. Even with all the difficulties we still accomplished the task in one hour. Thank goodness we had 4 extra screws that worked (actually only takes 2 but of the 6 we had, 4 fell into a place you could not reach into). Glue on the end of the screw driver finally kept the screws from falling into the black hole. It was an adventure and would do it again.

replaced both burner pans

Easy

Lifter the old items off and replaced them with the new ones.

First of all I had to find the right part from Partselect, which was very easy, delivery was fantastically fast even tho I didn`t order special delivery. After reading installation suggestions on the website, it was simple, open the top, disconnect the burners, removed the thermo from the inside. The only hard part was threading the sensor through the correct hole. I had to remove a couple of cover plates to see where the hole was. Put it back together, lit the oven and the temps were correct, as shown by an oven thermometer.

Wasn't a repair as much as it was a replacement. Burner pans and grates were showing their age. Searching for the exact match was easy and delivery was quick. These parts make the range look new again! Thank you PartSelect!