RB525G*R2 Hotpoint Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Marian from Inglis, FL
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
No heat on bake.
The first thing I did wrong was order the wrong part. Then later I did find the Model number on the side of the bottom drawer. I reordered the right part and turned off the electrical breaker. Removed the old element. I then installed the element in the oven with 2 screw nuts and pulled out the stove, took off the back panel and slipped the wire nuts onto the element. Very simple. I am really thankful there is a place to order the part and it came the next day after I ordered it. WHOW!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Todd from Mountain View, CA
- Parts Used:
- WB30M2
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Shorted out the burner... fat gets into the receptors on these old stoves.
The only hard part about putting in a new terminal block (and this time I had to replace the burner too, because that fried too) is stripping the stove wires, because that thermal insulation is very hard to get off. Otherwise, it's simple. In this case, I had already replaced this one (sigh), so had already cut & stripped the wires, so it was all easy. Frankly, the sane thing to do is buy a new stove, but wife is too cheap.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rob from Las Cruces, NM
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Lower baking element had burned out.
Using a nut driver, I removed the two screws holding the baking element to the firewall of the oven. I then pulled the baking element out exposing the two wires connected to it. I then used the same nutdriver to remove the nuts and detached the old element. I then connected the new element to the wires, pushed the wires inside the firewall and reattached the element to the firewall of the oven.
The time it took was literally a few minutes. Works like a new oven!
The time it took was literally a few minutes. Works like a new oven!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marie from Roxboro, NC
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Baking element had burned out and actually cracked in half.
It was so simple, I turned off the breker to the oven, unscrewed two screws holding in the element, pulled out until the wire connetion was exposed. I unscrewed those two screws, then placed the replacement part, put the two screws on, pushed back the wiring and insulation.Final step was screwing two screws to hold the unit to the oven back. So simple! The part was ordered regular mail and still was here in 2 days. Will recommend to friends for sure!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GREGORY from HOUSTON, TX
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Bake Element Burnt Out On Upper Oven
Unscrewed the element from the oven,disconnected the two screws for the electrical and reverse the procedure to install new element. Took all of about 10 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carolyn from Harvard, MA
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
oven wouldn't heat because coil had burned through
The part was delivered in 24 hours with regular
shipping and was simple to replace. Uncrewed
it, disconnected wires from the old one and connected
the new one. Cost a little more than $30 including shipping and the oven works great!
shipping and was simple to replace. Uncrewed
it, disconnected wires from the old one and connected
the new one. Cost a little more than $30 including shipping and the oven works great!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shannon from Birmingham, AL
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Baking element went out
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Removed the old piece and connected the wires to the new piece. I'm a woman and this took me less that 15 minutes to complete. Easy as pie. On top of that, I received my order within 3 days! Very impressive, PartSelect. Thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Worthington, OH
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Replacing a burned out oven heating element
First I removed two hex nuts holding the element's faceplate to the back of the oven and pulled the entire element straight toward me a couple of inches, pulling the element's ends and connections into view. I unscrewed the two screws holding the element ends to their connections, connected the new element, pushed it back in place, and screwed the faceplate tight again. The most challenging part of the whole process was finding the part number for the GE oven (it's on the frame of the storage drawer underneath the stove).
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rita from Apopka, FL
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Bake unit had burned out.
My husband removed the two screws that hold the element in place. He then pulled the element out about 3 inches and disconnected the two wires. He then removed the old bake unit and replaced it with the new one. He reattached the wires and pushed the element into place. Then he put the two screws back in that hold the element in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from North Walpole, NH
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Oven wouldn't heat, lower heating element burned out
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Removed the element and replaced with the new. Reattaching the wires and securing the new element back in place with the screws provided. Packed well, shipped promptly, installed quickly. Super easy.
Thank you.
Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phillip from Cary, NC
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
The Bake Element broke and when powered on it started to spark and flame.
First I read the already posted repair stories to give me confidence I could perform the repair.
Followed their steps -
Removed the two screws holding the plate to the oven.
Pulled out the element.
Removed the two screws holding the wires to the element.
Installed the new element by attaching the two screws (which were supplied) to the element.
Reinstalled the plate to the oven.
Tested it and it worked perfectly saving a costly service call.
Followed their steps -
Removed the two screws holding the plate to the oven.
Pulled out the element.
Removed the two screws holding the wires to the element.
Installed the new element by attaching the two screws (which were supplied) to the element.
Reinstalled the plate to the oven.
Tested it and it worked perfectly saving a costly service call.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MIKE from CHATHAM, IL
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
bake element burnt out
super easy - unpluged stove - unscrewed old element w/nutdriver from back of stove. unwired element - discarded. wired new element (2 wires). secured new element to back of stove. pluged stove back in. works great. Ordered part on Sunday, recieved it on Tuesday- VERY NICE SERVICE
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from Clayton, DE
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Original element stopped working
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...I copy and pasted this from their example - it really is that easy - this is a simple repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kelli from Moyock, NC
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench (Adjustable)
lower heating element wasn't working
I turned off the electricity, unscrewed the old one and disconnected the electric wires, then put the new one in just like the old one. It was very easy and now it works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from FALL RIVER, MA
- Parts Used:
- WB44X5082
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Bottom oven heating element was out
Very easy repair. 2 hex head screws to take the heating element out. Then 2 more slot head screws for the wire connections. Perfect fit and operation of the new heating element.
Was this instruction helpful to you?
Thank you for voting!