RB757EH4BB Hotpoint Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Charles from BENNETTSVILLE, SC
- Parts Used:
- WB27X45466
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Oven could not be turned off once settings were turned on except by unplugging hookup.
Took back cover panel off (upper) and removed the 4 1/4 inch nut screws. Used nut driver and removed the 4 screws holding control panel in place. Put new panel in place and unhooked electrical connections and installed on new panel. Plugged stove back in and checked operation. All OK, so then put back cover on and everybody is happy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Arthur from INDIANAPOLIS, IN
- Parts Used:
- WB27X45466
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
Oven would not get come up to temperature
I knew I had a bad control board. Using the repair videos, replacing this part was very easy to do. While I was at it, I replaced my oven temperature sensor. as well, and even though it wasn't bad, I replaced my oven heating element so that I could get some more mileage out of my 14-year-old range. The issue: after completing my repair actions, my oven element still would not heat. I double-checked my connections and I discovered I hadn't ensured one of the wires on the control board was properly seated. This was one of the wires that go to the heating element. After ensuring proper connection, everything worked perfectly!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BRINDIA from DOVER, TN
- Parts Used:
- WB24T10025
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Was burned out
Took back off and replaced.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lance from HAHIRA, GA
- Parts Used:
- WB17T10006
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Terminal block connectors worn out wasn’t making a good connection with the stove top burner
Cut 4 inch’s off the new terminal block wires then using my wire strippers stripped 1/2 inch off the ends , the old terminal block wires I stripped 1/2 inch at the ends using a wire nuts on both wires and electrical tape connected the terminal block to the stove plugged the new burner in and the burner worked 100%.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Allen from MOODY, AL
- Parts Used:
- WB56X31458, WB34K10034, WB02K10025
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Had to replace parts that I broke/bent trying to open warmer drawer.
Used the old drawer in disassembly as a guide to reassemble new bracket and cover parts. Black drawer cover did not look like old one so I had to weld washers on back side where screw holes were ripped open. Used pliers to bend drawer bottom back in shape where it was bent and assembled. Have to return Black Drawer cover since it looked nothing like old one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stella from PADUCAH, KY
- Parts Used:
- WB27X45466, 40A15
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Socket set
My electronic control board went out so I could not use my oven. My oven light blew as well.
I started with changing the bulb. I removed the small bracket that holds the glass cover over the bulb unscrewed the bulb and reversed to replace the bulb. To replace the control board I removed the top plate on the back of my stove took the small screw's out of the control panel and unplugged the wire's. Plugged the wire's into the right spots on the new control board and put it back together.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anil from Milpitas, CA
- Parts Used:
- WB24T10029
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burner spontaneously cycled without knob activation
First I cut the circuit at the breaker, and then pulled the range from wall to access the access panel. This top panel was held with 4 screws and removable with a standard phillips head screwdriver.
I then removed the 5 wire-crimped fasteners from the defective surface burner switch. (I first labeled these wires to ensure correct placement to the new switch). There were an additional two screws behind the corresponding knob that needed to be removed in order to completely remove the old switch.
The new switch was installed in reverse order to the steps indicated above (two screws behind knob, 5 wire-crimped fasteners, 4 screws to panel). Range was pushed back into position and breaker turned on.
I then removed the 5 wire-crimped fasteners from the defective surface burner switch. (I first labeled these wires to ensure correct placement to the new switch). There were an additional two screws behind the corresponding knob that needed to be removed in order to completely remove the old switch.
The new switch was installed in reverse order to the steps indicated above (two screws behind knob, 5 wire-crimped fasteners, 4 screws to panel). Range was pushed back into position and breaker turned on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alex R from Randoff, NJ
- Parts Used:
- WB23X5340
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
temperature sensor went
Took back panel off unplugged sensor and replugged in and worked like a charm!Sears wanted $400 and was going to 'overrepair"Got the 60 dollar part on here. UPS shipped to wrong address and customer service refunded my shipping and was excellent! would definetly use again!thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Melvin from Portland, TN
- Parts Used:
- WB24T10029
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Element blew hole in self then no power to burner.
Replaced burned element, did not fix no power problem. Ordered receptor replacement, replaced it, took less than 10 mminutes, but still no power to burned. Then ordered replacement switch, replacement too less than 10 minutes again and burner works fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ruth from JACKSON, MO
- Parts Used:
- WB24T10025
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
control switch had stopped working, burner wouldn't work properly
took out a couple of screws and replaced with new switch, plugged in switch wires. very easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MICHAEL from MORROW, GA
- Parts Used:
- WB30X46987
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Oven would not heat up
I removed the rear lower cover. Disconnected the terminals from the heating element. Removed 2 screws from the heating element from inside the oven. Removed the heating element. Reinstalled everything in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary Jane from La Junta, CO
- Parts Used:
- WB31T10015, WB31T10014
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
My burner trays were worn out and I needed new ones
I simply pulled the old ones out and replaced them with the new ones. It looks so much better and cleanes up well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roy from Au Gres, MI
- Parts Used:
- WB24T10025
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Could not adjust heat on burner.
Followed directions given by previous customers problems which we found on the internet.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- lucille from HAPPY CAMP, CA
- Parts Used:
- WB17T10006
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
burner was not heating
unplug it and plug the new one in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Melvin from WEBSTER, TX
- Parts Used:
- WB27X45466
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
THE FACE PLATE IS HARD TO GET OFF THE OLD CONTROL BOARD. USE A THIN KNIFE
THE INSTRUCTIONS THAT COME IN THE EMAIL ARE VERY GOOD. BE SURE TO TAKE A PICTURE OF THE WIRING.
Was this instruction helpful to you?
Thank you for voting!