RS47G*03 Hotpoint Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Old trim rings were rusted and soiled
Too easy to describe. Just lifted out the old rings and popped in the new ones. PartSelect is my go-to source for appliance parts both for my home and my job as maintenance man for residential group homes in my area. Website is easy to use, prices are good, shipping is always surprisingly fast. Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Eastchester, NY
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Element Sparked then split on the left side
Unpluged Stove, Unscrewed the wires attached to the Element in the back of stove after I removed the cover. Removed the two screws that held the Element at the back of the oven compartment. Then replaced the Element with the new one and put back the screws, the wires and the cover in the same sequence iI took it apart. Plugged it back in works like new!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Melvin from Houghton, MI
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Heating element burned out
Repair was super easy - read the other stories posted. They give more than adequate instruction.
Amazingly helpful website. Found the part, instructions to install, and able to order in less than 20 minutes!
Amazingly helpful website. Found the part, instructions to install, and able to order in less than 20 minutes!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenny from Greenville, MS
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Oven Element would not heat up
I first turn off the 220 power braker to the electric stove. Making sure the stove and element is very cool.
I then removed the two screws that hold the lower baking element in place. Pull gently on the element not to break the wires from the wall of the stove (about 3 to 4 inches).
I than unscrewed the right and left wire attached to the element with the nut driver. (This old element was attached with small nut screws. The new one has screws that use a screw driver). Keeping the wires apart, I removed the old element and replace it with the new element part.
In replacing the new element, facing the stove I connected the black wires to the left side (my left hand) and the white wire to the right side (my right hand) with the new screws using a screw driver. REMEMBER TO REPLACE THE WIRES BACK THE WAY THEY CAME OFF WHEN THE STOVE WAS WORKING PROPERTLY. Attach the element back to the stove and turn the breaker on. Easy to do job.
I then removed the two screws that hold the lower baking element in place. Pull gently on the element not to break the wires from the wall of the stove (about 3 to 4 inches).
I than unscrewed the right and left wire attached to the element with the nut driver. (This old element was attached with small nut screws. The new one has screws that use a screw driver). Keeping the wires apart, I removed the old element and replace it with the new element part.
In replacing the new element, facing the stove I connected the black wires to the left side (my left hand) and the white wire to the right side (my right hand) with the new screws using a screw driver. REMEMBER TO REPLACE THE WIRES BACK THE WAY THEY CAME OFF WHEN THE STOVE WAS WORKING PROPERTLY. Attach the element back to the stove and turn the breaker on. Easy to do job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Elkton, VA
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
bottom element was burnt out
removed 2 screws that hold the element in place, then pulled element out took 2 more screws out and reversed proc. I couldn't have had a better rep to help me find the right part. Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary Grace from Nashville, TN
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The baking element burned out.
I had a friend of mine who came to my home equipped with screwdrivers and flashlight. After turning off the electricity at the fuse box he removed the oven door (for easier access),removed the screws,pulled out the existing element far enough to disconnect the wires, placed the new one into place, connected the wires, screwed the new one into place
turned the power back on, turned on the oven and after about 15 seconds, the element began to turn from a dark gray to a light color beginning to turn orange.
turned the power back on, turned on the oven and after about 15 seconds, the element began to turn from a dark gray to a light color beginning to turn orange.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOHN from MELBOURNE, FL
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Lower heating elemet burned out in oven
It only took 15 minutes and a nut driver to replace.The part was $22,well worth keeping my oven going for a few more yaers
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Gordonsville, VA
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Baking element burned out
Unscrewed the plate and unplugged the old element and plugged the new one in, screwed the plate back on. Done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Decatur, IL
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Element Had Broken
First we unplugged stove, if wired into circuit shut off in breaker box. Undo four screws on back cover and detach wires from element. Remove oven door by pulling open and sliding it up off hinges. Undo two screws holding element to back wall of oven. Slide in new element and replace screws in back wall. Replace door. Slide wire leads on new element in back, at this point we plugged range in and tested element to see if heating. It worked so we replaced cover, slide range in and leveled it with wedges. Time for pizza.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rodney from Nokesville, VA
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Oven Heating element burned out.
The repair is simple. Unplug or turn off power to stove. Remove the 2 visible screw where the element connects to the back of the oven. Pull the element with back plate out. The back plate is part of the element. Remove 2 screws that connect wire. Mark which color connects to which lead. Re-assemble in reverse order. Takes about 15 minutes,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from Las Vegas, NV
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
burnt out bake element
This was a simple repair. Be sure to turn breaker to stove off before you start. Then remove two small screws holding element to back of stove, pull out element and disconnect two wires and remove. Reverse the steps for installation.Very simple
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephan from Gladstone, MO
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Replace the large heating element.
It would have gone with ease but the screws holding the element to the conductors were not original. Once those were removed, we were able to use the screws included and were done in 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephanie from Kitty Hawk, NC
- Parts Used:
- WB32X10013, WB31X5014
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
needed to replace drip bowl and trim ring
The replacement drip bowl and trim ring fit perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- suzanne from crofton, MD
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Heating element in oven gave up on Monday before Thanksgiving.
Totally pleased! I ordered the part Monday evening, and it was delivered Wednesday morning. Awesome! Was able to change the part in about 15 minutes. Thanksgiving was a success! Part Select saved my Thanksgiving! Highly recommend :) Thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- david from estero, FL
- Parts Used:
- WB44X5082
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
bottom oven burner burnt out
fairly easy. Only four screws. The only problem was reaching the back of the oven without hurting my back and being careful not to over tighten the wires to the new burner ends. I wish all repair were as easy.
Was this instruction helpful to you?
Thank you for voting!