RB734*J4 Hotpoint Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- John from High Point, NC
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Bake element burned out
I first looked at a video PartSelect had done on replacing the bake element in a stove. I disconnected the stove's power plug from the wall, removed the baking shelves, and removed screws holding the cover plate for the old bake element with a nutdriver. I removed the two screws holding the power wires to the bake element and replaced the bake element with the new element purchased from PartSelect. The cover plate was repositioned by using the nutdrive to tighten the cover plate screws. After reinstalling the bake shelves and plugging the oven back in, the repair was finished.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael L. from Auburndale, FL
- Parts Used:
- WB44X5082
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Bottom element burned out
I have some electrical experience. It was simple to remove and install. You just have to pay attention to wiring upon removal and installation.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sally from Ravenswood, WV
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Element replaced
It was quite easy-hooked up the wires replaced screws to hold it in place-finished!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- marlene from san rasael, CA
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Element was not working
Removed old element by unbolting two nuts, replaced with new element and two new nuts that were included. Very easy and worked fine.Wish all repair jobs were this easy!Great service with ordering and prompt delivery, too.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patrick from Riverton, WY
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Oven woudn't heat - lower element didn't heat
Took out the two screws that held the old element. Disconnected (unscrewed) the two power cords. Screwed in new power cords and put two screws in new element. Works like a charm. Took longer to get the new element out of the box than to replace it! Thank you!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Tavares, FL
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Lower element burned out
Wasn't sure what to do had a friend come over and it was fixed in less than 15 min. The shipment was really fast and although I only had a partial model number because of age of the unit your search engine found it. Thanks all, my wife is very happy. Your the best!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- harold from burlington, WV
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
baking element broke and would not heat
Shut electric off to range[circuit breaker], removed door and baking racks, removed two screws holding element to back of the oven compartment, pulled the element out to expose the wires, removed screws fastening the wires to the element. Discarded the damaged element and installed the new one in the reverse order. Turned on power and tested. Everything worked fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- david from estero, FL
- Parts Used:
- WB44X5082
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
bottom oven burner burnt out
fairly easy. Only four screws. The only problem was reaching the back of the oven without hurting my back and being careful not to over tighten the wires to the new burner ends. I wish all repair were as easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- mark from salisbury, NC
- Parts Used:
- WB44X5082
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
replacing bake element
1st. turned breaker to oven to off position. removed oven racks from oven. removed "2" small metal screws that held baking element in place to back of oven. easily pulled element toward front of oven. removed two additional metal screws that connected "element" to oven wiring. connected new element to wiring using screws, pushed back in place to back of oven, and replaced screws that held baking element in place. replaced oven racks and turned breaker to on position. total time apprx. 7-8 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randall from Fredericksburg, VA
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Bake element burned in two and was sparking
The bake element is very easy to replace. Turn off the circuit breaker to the stove. Two screws (1/4" socket needed, not screwdriver) come out to release the plate, then two more screws of the same size to unfasten the element to the stove wiring. Reverse the process to put the new one back in. I let my fourteen year old son do the whole thing. By the way, the photo of the element on the web site did not look like the element in my stove. I called customer support and was assured that it was the proper part. When it arrived, it did exactly match my element. The photo on the web site was incorrect. (Part number PS249466)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Laurie from Jonesborough, TN
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Wrench (Adjustable)
bake element burned out
Took the old one out, measured it, ordered the appropriate size, intalled the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ANDREW from CHICAGO, IL
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench (Adjustable)
Broken Bake Element
Removed bolts from fixing plate, pulled out existing element, unscrewed wire connectors and installed new element in reverse order of removal. This is an old stove from the 60's or 70's so I was glad to get a replacement part and fit it myself so easily.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Hamden, CT
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Original bake element burned out
Followed directions left by a previous user on PartSelect: 1. open oven door and lifted it off hinges; 2. Unscrewed mounting element mounting plate from rear of oven (may need nutdriver, allen wrench or screwdriver) 3. Unscrewed electrical leads from element; replaced with new element and reversed the steps.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Bethlehem, PA
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench set
bake element in oven burned out
Removed old element from back of oven with closed wrench and removed wires from element with screwdriver. Took me longer to find screwdriver than to install part. Finding part and ordering it was a snap. Got part in day and half. Great service and price. This is the place for parts and instructions. Will definitly use it again. My wife thinks I'm a genious. Thanks PARTSELECT.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Halimah from Charlotte, NC
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Bake element burned out.
My son used a screw driver and needle nose pliers to remove the old element. He then slide the new element on, put the screws in and he was done.
Was this instruction helpful to you?
Thank you for voting!