RB632GW3 Hotpoint Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jeffrey from Mason, TX
- Parts Used:
- WB44X10009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Bake element broke into pieces!
I ordered to correct part from PartSelect with relative ease given I know nothing about oven repair. What's even more amazing, my wife who is not mechanically-minded, took the element home and replaced the broken one in 15 minutes with nothing but a pair of pliers. We live 22 miles from town so a repairman would have cost over $100 just to show up. Total cost = $36!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jason from Arlington, TN
- Parts Used:
- WB44X10009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Element burned through
With the oven unplugged, I removed the protective plate from the back of the oven, and then I unplugged the old element from the contacts. There were two screws holding in the element inside the oven- after unscrewing these, the old element slid right in. After reconnecting everything and plugging the oven back in, all was good. Pretty simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Emerson F from Cambridge, OH
- Parts Used:
- WB44X10009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bake element burned a hole in the element
First i removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires.
Very simple and easly job.
Very simple and easly job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Douglas from Acampo, CA
- Parts Used:
- WB44X10009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
The old element blew up
Removed both racks, removed two screws holding element in. Removed two screws holding wires on element. Drilled holes in new element where the push-on connectors are attached so I could attach the oven wires to the new element. Attached the wires and screwed the element to the oven. Fit perfectly and the temperature of the oven matches the control knob finally!
Thanks.
Thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eula from Greenville, MI
- Parts Used:
- WB31K10266, WB31K10265, WB30M2, WB30M1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
needed new burners and drip pans
They fit perfect
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DEBRA from DULUTH, MN
- Parts Used:
- WB30M2
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I Ruined My Burner -- This Was A Solution For Me...
I simply pushed the new burner into hardware. I then tested it to see if it works. . .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patti from Carnation, WA
- Parts Used:
- WB44X10009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
bake element did not heat
shut off power, removed self tapping nuts, removed element, put new element in, re-attached nuts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harold from Gloversville, NY
- Parts Used:
- WB30M1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
burned-out six inch electric stove- top burner
Removed the old and slipped in the new.No problem and it works fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LISA from GLENDALE, CA
- Parts Used:
- WB30M2
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Electric stove 8" burner needed to be replaced
Installation took 30 seconds. Your website was easy to use & the part received was just as described. It arrived beautifully wrapped & in just a few days. ABSOLUTELY AWESOME!I will recommend your site to everyone.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeannette from Haskell, NJ
- Parts Used:
- WB30M2
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burner heating coil element would not get hot.
I pulled out the heating coil and pushed in the new coil. I turned the stove top on and heard a sound like "dzzzt". I immediately turned off the burner and waited for it to cool, then pulled it out. The part had a burn melt on one side of the end prong. It turns out that the part that the burner plugs into needs to be replaced. Actually, the stove top is over 20 years old and my landlord will have to replace the whole unit. So it turns out that I didn't need to order a surface element after all, but it was very easy to install!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MARLENE from EUGENE, OR
- Parts Used:
- WB30M1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
element broken at contact point
ordered new surface element and pushed in to conector turned on switch to test and works fine thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lois from Sarver, PA
- Parts Used:
- WB30M1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Plug-in surface element was covered with a melted on forever microwave plate
Just put it right into the receptacle. I want to add...we had gone to our local appliance store and brought home a wrong-size unit. Got online and your website came up. It was easy to find the correct part, ordered it and it arrived 3 days later. I have already recommended your website to 2 of my friends. One very good experience!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Don from Pocahontas, AR
- Parts Used:
- WB44X10009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Oven element burned out
Disconnect power to range, remove fan cover (4 screws).
Remove old element (2 screws).
Pull off wires from old element.
Discard old element, clean bottom of oven.
Slip wires on terminals of new element.
Install new element,and fan cover.
Reconnect power.
Remove old element (2 screws).
Pull off wires from old element.
Discard old element, clean bottom of oven.
Slip wires on terminals of new element.
Install new element,and fan cover.
Reconnect power.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Goodyear, AZ
- Parts Used:
- WB30M1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Small burners would not work
ordered parts and disassembled old burners and installed new ones. All the parts were in the box when delivered.
Helping my 80 yr old mother-in-law very happy.
Got parts in for one of her 81st birthday present she was thrilled.
Helping my 80 yr old mother-in-law very happy.
Got parts in for one of her 81st birthday present she was thrilled.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andrew from Tyler, TX
- Parts Used:
- WB44X10009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Element went bad.
Used a nut driver and removed to studs and pulled the old element out and disconnected the two wires. Then connected the new element and put the studs back. It was that easy. Great website and it only took 5 minutes to order the part and received it on time. Plus my wife was trying to cook thanksgiving dinner. Thanks
Was this instruction helpful to you?
Thank you for voting!