RB800SJ2SA Hotpoint Range - Instructions

replaced oven clock control ref maintenance manual, 4 screws and 8 wires. plugged in new control and op checks good.

Removed to screws on bracket and sliped the element out. Inserted new element and installed bracket and two screws.

verified switch operation , checked continuity of burner element found open ordered new part and installed next day
after extremely fast
service from partselect thank you

removed the top section on stove and removed the wires off swtitch and put on new one then put new switch in

Isolated to control switch.

Replaced

best to pull stove out away from wall connect from behind stove

This repair was quite a bit more difficult then what had been described on the web site. First off, I have a double wall oven that is built in. Sliding it out of the cabinet was difficult and because oven was hard wired, I had to disconnect the actual wiring from the oven back. . Positioning the oven and allowing for it to rest on a support bench was the most difficult part The oven is heavy. Eventually, removing the back and top panels of the oven revealed the sensor connection. I was then able to feed it through the oven and reconnect all the wiring harnesses.. Getting the oven back in the cabinet was equally a challenge. But it did seem to fix the problem with over heating.

After watching the demonstration on YOU TUBE by two separate persons, , I felt I could accomplish this repair job by myself. After all, if a 9 months pregnant lady on YOU TUBE can do it in 15 minutes then so could I. However, my particular stove turned out to be a bit more involved, and different than those whose demonstrations I had viewed! .. First turn off your electrical power at the circuit breaker. There is no need to unplug the stove, just test by turning it on and observing if the display is lit or the burners come on. If it doesn't then you are good to start the repair with the power off. 1) Open the oven door, then bend over and check underneath. There are two screws one on each side at the front. Using an 8 mm socket wrench undo those screws and put them in a safe place where they wont roll away. 2) I would suggest using an old towel or an old sheet once you have the stove top lifted to cover your work surface, so if you drop any little parts that might roll away, you will be able to just pick them up without a problem. Next you will need something to prop the stove top open or someone to hold it for you. I used the box that my new element came in and that worked well. 3) Here's where my stove differed.. I had a metal retaining bar across the two front elements holding them up in place. .. I unscrewed the two small screws that held it in place at the edge of the stove. (I just did it on the side where I was replacing the element). This does not release your element just the bar so you can get access to the element. 4) Next, using your pliers you will see a couple of round washers that have teeth, these are holding a spring in place on a metal peg, this keeps the element from falling or moving out of position.. It was a bit difficult releasing the washers but I eventually did it, with my pliers, and then had to straighten the washers out for use afterwards 5) Once the washers are off, this frees the spring and allows the element to be removed. from the bar. 6)Next, I recommend taking a picture of the wiring, so you will know what goes to where. There are four wires on the old element, so I just followed the color coded placement and fasten them in the same place onto the new element. The wires are a bit stiff to remove, and if you are using pliers be careful as they are fragile and could break. 6) When I removed my GE replacement element from the packaging, it turned out to be a little different, and did not have the two metal pegs on it. In order to make it fit so I could do the repair. I unscrewed the two pegs from the old element, then counting around the outside holes on the new element to get them in the exact same place, I then attempted to screw them in.. This was the difficult part as they did not easily fit, and I had to ream out the holes to get the posts to screw into the new element. 6) Once that was done, the rest is easy just putting it back together the same way you took it apart. With the pegs screwed in place and the four wiring clips put on the new element, then it should not take long to complete. Next fit the spring over the metal peg first, then put the peg through the hole on the retaining bar. Make sure you get them lined up in the correct position. If you don't then they will be out of alignment with the Ring marking on the glass surface. Check this before you get it all put back together. The retaining bar has four holes in it, so you will see what I mean. The metal pegs on my element went into two opposing holes. Once that is done, the spring goes over the peg, then the peg goes into the retaining bar, and lastly, the small round washer fits the bottom of the peg to keep the spring held tight and the element in place on the metal retaining bar. You are almost done. Next simply put the retaining bar back up, make sure your element lines up on the top of your stove in the position it was before, then put the two small screws

I miss diagnosed the situation at first. When the top element only heated up I thought the control was the problem. Wrong. Apparently both elements heat up during initial start up. It turned out that the bottom element was not working so it needed to be replaced rather then the control. Now both are replaced and the oven is now back to original status. Entire repair cost about $80. I saved over $100 by attempting this myself. Easy fix. Obviously I am not a pro. My local hardware store had a generic heating element that worked just fine and only cost $22. Two screws to repair after removing the back panel. Remember to pull the plug before you begin and after the repair put all panels back on before plugging back in. Pizza anyone?

Remove lower drawer and contents. Unplug unit. Tilt range on its back for easy access. Tie open oven door to forward legs with sturdy rope. Use small socket to remove 2 back screws and 2 forward element hanger screws. Detach broiler element connections from wire clips(2). Insert new element, attach 2 new connections to clips first. Install back socket screws. Install front socket screws for element hanger. Slide in oven shelves. Release oven door rope. Lift range to normal position. Replace lower drawer. Plug 220 in. Test oven element then broiler.

Purchased the board installed it and saved about 130 dollars.

Took out the old control module and removed the sticker and reattached sticker to new part and installed the plugs, put the screws back in and it started working, thankyou so much.

The only tool needed was a nutdriver to remove the lamp socket. I needed my head mounted light to see what I was doing, and everything went smoothly from there. Simple job.

Used the TS guide, because I had no idea what the problem was. That was easy step by step. Thanks. Gave me a list of two parts that could fix the problem. Picked the higher percentage part (97%). Followed the simple install instructions and it was successful. One problem I did encounter was the two wires that it connected to were short. Removed the back center plate to gain access to the wires. I was able to extend them enough to make the connections to the bake element. If not for that the repair would have only taken maybe 10 minute's.

I ordered the part on a Monday and Tuesday afternoon I received it! I went a route I often take first. I read the instructions of others before starting my job and opened the top of the range. There are two screws under the range top in front near the oven door, one on either side, that must be removed. After this I opened the top of the range and positioned a piece of 2X2 about 20 inches long at an angle to hold the top up while I worked on the burner. I then used my phone to take a close up picture of the old burner while in place in my range so I could refer to it when putting the new one in place. I then took a pair of needle nose pliers and pulled off the wiring, then removed lock washers under the burner and removed the old burner, being careful not to lose the washers and springs. I took the new burner and layed it along side the old one to see exactly how it would be placed under the glass cover. I replace the springs and lock washers then referred to my photo and replace all the wires to the burner as they had been. Then lowered the top in place and put the screws back in place. That was it. I'm a 67 year old female, if I can do this, anyone can!