RGB740BEH2CT Hotpoint Range - Instructions

I could not get these grates clean, so I called Partselect and they helped me find the model of the same stove that had black grates, drip pans, and burner caps. I ordered the black grates one afternoon, and without paying for expedited shipping, they arrived the next day! They were in original GE boxes (since they make Hotpoint). I am happy about the whole experience.

A G.E. tech came out and quoted $500 to replace the circuit board. I unbolted the board myself and used the camera in my phone to take a picture of the wiring. Then I came to PartSelect.com and using their diagrams found the replacement board for $75. It came in the mail a few days later. I used to picture in my phone to reconnect all the wires, bolted everything back up and baked some cookies. Thanks PartSelect for making my repair job simple and inexpensive.

Really self explanatory. Removed the old drip pans and put in the new. No tools required. However, I would like to say I received the parts the day after I ordered them. EXTREMELY FAST SHIPPING!!

openend stove top disconnected wire pushed out old sparker inserted new one closed lid game over

Removed the two screws put the heat shield off the old one onto the new one put new bottom in and tightened two screws. Done #38. 69 Cost of part with shipping cost included.

While i was inserting the new lp,gas orriface to the right rear burner tube I dropped the oriface.Without looking i popped the top of the burner unit, like most older type stoves, and thats when i ran into my problem. I realized the burner tube assemblies are attached by 3 screws to the top cover.Not attached to the cabinet as the older models, Basically cracked both front aluminum tubes trying to retrieve the dropped oriface. so i had to replace the burner tube units, which involved removing 3 screws, and loosing up and removal of the nut to the main gas tube. extremely easy repair, next time i`ll try to remember look before i leap,total time to (r+r)burner tubes about 20 minutes.Parts select pulled me out of the fire on this one, great staff and service, with quick delivery.

Pull plug and shut off gas! The lower oven burner is held in with two rear and one front screws. I removed the top floor of the oven (two hand tightened screws at the back), the bottom drawer, and the front door (just lift it off the hinges). This allowed me to access the burner, and I removed it by unscrewing the three screws, unhitching the igniter connector, and lifting the burner and igniter up and out. I connected the new igniter on the new burner before installing it in the oven, and found that the connector did not match (I was warned about this possibility on the PartSelect site), but instead of splicing the wires together, I cut off the connector on the new igniter and replaced it with the connector of the old igniter. Then I screwed the burner into the oven, recoupled the connector, replaced the floor, drawer, and door, and I was done! It took about 45 minutes.

I remove the damage handle from the oven door,Then i install the new door handle with no problem.The tools i used was a hand nut driver and a phillip #3driver.

I was very pleased with how quickly the new oven rack arrived and it was a perfect fit. Thanks.

Unplugged the appliance for safety. Removed two 1/4" screws that held the assembly in place. Carefully removed the wire guard that retains the glass shield. Unscrewed old light bulb and replaced with new part. Reversed the steps after cleaning glass cover.

I ordered a new display from the internet. I removed the panel where the display is housed, unscrewed the entire display assembly and unplugged all wires connecting it. (I made a drawing and noted colors of wires) I removed adhesive face of display and replaced it on the new display. I then screwed in the display and reconnected the wires as per my notes. I reassembled the panel and applied power and it worked like new.

Thanksgiving was coming and I needed extra oven space. So I ordered an additional rack. Installation ... just put it in the oven. My part came the day after I ordered it.

determined that the top of the burner was melted and malformed. Repair was simple: lifted off the damaged burner and slipped the new one in place.

While I was waiting on another part to arrive, I decided it would be a good time to do a thorough cleaning. When I lifted the top of the range, I lifted it to far and cracked both front burner tubes. The top of the range should not be lifted more than 4 inches without removing the 3 screws that hold each burner in place. When the new lines came in, I removed both front burners, knobs, and then removed the front plate behind the knobs using a Phillips screwdriver. The screws are located on the bottom of the plate. Using my adjustable wrench I replaced the lines. Then I CAREFULLY bent the gas tubes and remounted the burners. Over all an easy install. Just be careful, the gas tubes are aluminum and will break very easy. This is the second time I used PartSelect, and I am very satisfied.

removed two screws and took out bottom tray and put the new one in and replaced the screws.DId it my self.