RB757WB1 Hotpoint Range - Instructions

Very easy repair, Pulled burner coil out, removed old burner bowl. Put in new burner bowl, plugged burner coil back in... easy as 1,2,3

Removed burner element and put in bowl

Removed all surface elements, threw away old burner bowls, put the 3 older surface elements back in place and inserted the new element.

The burner bowls look great. Now I won't wait so long to replace.

Thanks.

very easy..pull out burner, slide new one in..like a plug.

none of the "replacement" burner bowls i found at
store like home depot/ bed bath and beyond and such didn't fit.. so much for universal sizing..

thank you parts select.

a very satisfied customer

Pulled out burner and put new bowls in. Looks like a new stove!

Took 5 minutes to replace the 4 bowls. Ordered the bowls one day & they arrived the next day All went perfect.

Turn the breaker off to the oven.Removed both wire racks,using a 1/4 nut driver unscrewed the old element.The flashlight was so I could see inside the oven.Having removed the two screws ,the old element came right out.With my needle nose pliers removed the wires one at a time,replacing them on the new element as they came off.Replaced the two screws holding the element ,replace my wire rack, turned the breaker back on.As for the price for the part ,it was less than a service call from a repairman,which would not have included the part.

Per the instructions included with part.

Upon removing the back panel of range with screwdriver to gain access to elelctric clock control. Unit was taken out with the use of a 1/4'' nutdriver. After following included instrucitons with replacement part. Part was an unpluged/pluged in operation. Works great. No service technician needed. Thanks gain.

First I turned off the circut breaker. Then removed the two wire racks. Then I removed the two 1/4" hex head screws holding the rear of the element in place. Pulled the element out far enough to remove the two wires. Discarded the old element. Installed the new element in the reverse order and turned the breaker back on. Took no more than 10 minutes. Ordering the part was easy. The diragrams with measurements of the part made it easy to insure that I was getting the right part. I'm sure I save myself at least a $65 plus service call. Not to mention a mark up on the part itself. I will use this website in the future if needed. Thanks

1. Removed the back panel.
2. Disconnected the wires from the old switch while connecting wires to the new switch one at a time.
3. Installed the new switch and broke off the excess metal on the post which fits into the burner knob on front of the range.
4. Replaced the burner knob and replaced the back panel.

The repair went quickly. First, I switched off the circuit breaker. Then, after lifting off the oven door to lighten the stove, I pulled it away from the wall for easy access to the part. I pulled off the oven control knob. WIth my socket wrench, I removed the 6 or so screws from the back cover of the stove. Now, I was able to see the clock timer and switch. Just a few phillips screws held it in place. I removed it, and struggled just a bit to remove the wires from their attachments to the old part. I wired the new part, one wire at a time, carefully comparing the function of the wires, not just the colors of the wires, using the clear and simple diagram that was included with the part. A sharp knife under the edge of the faceplate of the old part allowed me to pry it off and reuse it. Thus, I had my up and down arrows, the labels for clock and timer. It didn't shatter, as I feared. In fact, that faceplate was held on with only a small area of adhesive around the edge. I placed the faceplate from the old part over the front of the new part, alligned it in the opening and tightened it down with the screws I had removed. I replaced the oven knob. I switched on the breaker. The broiler worked, the timer worked. I felt powerful. I unexpectedly impressed my teenage children with my skills here, as I replaced the back cover of the stove, and set it back in it's place then replaced the oven door.
The replacement part was the same but with some differences in internal shape. This did not affect the fit. The wiring configuration was not the same. This added to my time as I had never done this before and needed to feel completely confident before proceding. The part came with a clear diagram of the wiring-- ground, line in, broiler, and oven. 4 attachments. The 3 ground wires are joined to one connector in my stove. A careful look was enough to assure me that though my colors were not the same, the basics were the same.
I feel this was a simple job. My stove and oven look and work like new.
And my husband thinks I'm amazing.

Removed oven from cabinet. unblug old sensor pluged in new and reinstalled oven. Esay repair though wish oven was designed so did not have to pull itout of cabinet which requires disconect electric cabel

I downloaded the installaion manual from the web for this model. First htings first, I located the circuit breaker for the oven and turned it off. Removed the lower trim piece from the bottom, next lifted the oven door off its hinges and set it to the side. I then wrapped a couple of small towels around the hinges for the door as per the manual (the hinges can pinch a finger). I then removed the four screws which secured the oven into the cabinet. Next I slid the oven forward allowing me access to the rear. I removed the pieces from the rear to gain access to the sensors connector, and unpl;ugged the sensor. Went around to the front and unscrewed the 2 screws securing the sensor and removed it. I then installed the new sensor, replaced the rear covers, slid the oven back into the cabinet, secured the four screws, snapped on the lower trim, remounted the oven door, and turned the breaker on. Oven working fine now.

First dressed out with my hard hat, work gloves, dust mask then locked all the doors to prevent intruders from disturbing my concentration. During the installation took video for you tube broadcast and then invited friends and neighbors to witness the accomplishment! Made a sloppy soup to see how the drip pans worked. A+. Received quite a few back pats and atta boys. Most challenging aspect to this endeavor was unwrapping the packaging which was well done thank you. The whole experience left me refreshed and ready to take on the world! Thanks for asking!