RB734*J8 Hotpoint Range - Instructions

removed the two screws, unsnapped the burnedout element and snapped new element in place, replaced two screws.

The bake element in my 17 year old GE free standing electric range became defective. This element has 2 terminals -- black (240V) and white (neutral). While removing the element from the range, a 2nd black wire was pulled out of the back of the oven. This wire had a bare terminal connection and apparently had been loose behind the oven shell for all these 17 years. Inspection of this wire showed it carried 115V. I wrapped this wire with electrical tape and reinserted it into the insulation behind the oven shell.

Unplugged range. Removed old element from back of oven which was held in by two screws. Unscrewed the wires that were attached to old element and screwed them into the new one.

No. 1 thing I did is I unplugged power supply to oven, second- unscrewed two screws that was holding cover plate and removed cover plate with a set of pliers, pulled element out and unscrewed two screw with power wires and installed new element, tightened screws and re-installed cover plate, tested oven turning on oven and in a few seconds element got hot, job done!

First I turned off the breaker to the oven,
then I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I placed the new element in the oven, reconnected the wiring and replaced the two screws in the mounting bracket. I reset the breaker and turned the oven on to about 450 degrees for 30 minutes to burn off the new smell of the element. This job was very easy and I saved about $100 from paying a service to do it.

Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Then I replaced it with the new element that took only two days to arrive and that was without paying extra express shipping fees. It couldn't have been easier. I didn't even wait for my husband to come home and install it. I had an oven-baked meal ready when he got home. I was very satisfied.

Unplugged oven. Removed the two screws from inside the oven that secured element to the back. I then removed the protective cover for the plug from behind the oven-three screws. Disconnected the element from the electrical wires, removed and replaced the element. And reassembled the cover and all the screws in reverse order. Plugged it in. Presto, 5 mins and works great.

Unpluged Stove, Unscrewed the wires attached to the Element in the back of stove after I removed the cover. Removed the two screws that held the Element at the back of the oven compartment. Then replaced the Element with the new one and put back the screws, the wires and the cover in the same sequence iI took it apart. Plugged it back in works like new!

My husband removed the screws holding the element, disconnected the wires from the old element. He then reattached the wires to the new element, putting it back into place, tightened the screws, and we were cooking again. The shipping service was GREAT! I ordered the part on-line and it arrived next day! Thanks!

I removed the original element with socket set (two hex nuts). I removed the element and face plate, reversing the steps when installing the new element. It was simple.

The bake element is very easy to replace. Turn off the circuit breaker to the stove. Two screws (1/4" socket needed, not screwdriver) come out to release the plate, then two more screws of the same size to unfasten the element to the stove wiring. Reverse the process to put the new one back in. I let my fourteen year old son do the whole thing. By the way, the photo of the element on the web site did not look like the element in my stove. I called customer support and was assured that it was the proper part. When it arrived, it did exactly match my element. The photo on the web site was incorrect. (Part number PS249466)

First we unplugged stove, if wired into circuit shut off in breaker box. Undo four screws on back cover and detach wires from element. Remove oven door by pulling open and sliding it up off hinges. Undo two screws holding element to back wall of oven. Slide in new element and replace screws in back wall. Replace door. Slide wire leads on new element in back, at this point we plugged range in and tested element to see if heating. It worked so we replaced cover, slide range in and leveled it with wedges. Time for pizza.

The repair is simple. Unplug or turn off power to stove. Remove the 2 visible screw where the element connects to the back of the oven. Pull the element with back plate out. The back plate is part of the element. Remove 2 screws that connect wire. Mark which color connects to which lead. Re-assemble in reverse order. Takes about 15 minutes,

CAUTION: Make sure stove is unplugged as there is still current with it off! Removed 2 screws to pull old element out & 2 screws on electrical wires. Put new element in & screwed all screws, very easy repair. A big THANK-YOU to PartSelect for getting the part to us so fast!!