RGB745WEHCWW Hotpoint Range - Instructions

This web site is awesome!!! their forum told me what part i needed, and they shipped it out, super fast, i couldn't hardly believe it! I tried using the Sears Parts web site for my "kenmore" oven and that was a joke, seriously! no more kenmore for me, thanks. It took this site to figure out that i really had a G.E. with a kenmore name on it.
I found out that even though the old ignitor glows well, it may not pull enough amps to open the gas valve.
First i disconnected the two wires on the gas safety valve that lead to the ignitor. These are accessed after taking the bottom drawer out. Then using a nut driver, i took out the two screws holding the bottom of the burner tube. Then inside the oven, i took out the racks and then the two screws in the back on the bottom. Then took out the bottom plate. I removed the one screw on the front of the burner tube, and removed the burner tube with the ignitor attached. I cut the wires off the old ignitor and attached them to the new ignitor with the supplied ceramic wire nuts. I attached the new ignitor to the burner tube and put everything back together. The bottom screws on the burner tube were very difficult for me to reach. Almost impossible to get both hands there to do the job.

Remove the front door-lifted off(no tools) removed the floor of the oven (2 standard nuts at the rear). nut driver to remove the igniter. Took longest to untwist and retwist wires & dropped screws. reassembled and tested...worked perfice. this is the 4th time I've used Parts Select and It's great....Thanks and keep up the good work!

Removed the bottom plate inside the stove by removing two back screws. The burner was exposed. roved a total of three screws on gas burner to remove the entire assembly. Removed two screws from the old igniter and then put new one on. Save the old connectors because they have unique connectors. Cut old wire and strip 3/8 inch of wire cover off. Using the supplied wire nuts. Caution use only supplied wire nuts because they are meant for heat. connect old wire to new wire of the new igniter. Reverse order of screws that you did for the job. That is it

Go to utube videos for this are there

PULL RANGE OUT FROM WALL & ALSO REMOVED OVEN DOOR BY SLIDING UP. WORKING FROM INSIDE OVEN & ALSO BEHIND I REPLACED PART . ALWAYS " UNPLUG " RANGE BEFORE YOU START.

Start by shutting off the main gas supply to the range and unplugging the electric cord.
You will first need to take the plastic control knobs of from each individual burner (they should slide straight off).
Next, you will need to remove two phillips head screws on the front face of the panel. They are located on the right side of each rear valve burner stem that is sticking out through the panel.
Next, open the oven door, locate and remove the three screws on the bottom of the front face panel. The front panel should now come off exposing the top burner manifold and all of the valve burners.
The next step would be to take the burner grates and each round burner cover off (no tools required). This will expose the top of each individual burner. You will see screws that hold each individual burner down to the stove top. On my stove the heads were all rusted and I could not remove them. If you can remove all four of your burners and disconnect the wire on each ignitor and set the burners aside.
Next, go back to the front of the stove where you took off the panel and you will see two metal clips on each side of the stove top. Push each one of these in with a screwdriver and gently lift up on the stove top. It should hinge up towards the back of the stove and give you full access to the burner valve you need to change.
Next, use a box end wrench (I think it was 1/2") and remove the gas line attached to the burner valve. After the gas line is removed, take out the bolt and clamp that holds the burner valve to the manifold. The old valve should drop out.
Install the new valve making sure the rubber gasket is seated properly, reattach the clamp and bolt and reinstall the burner tube line.
Before you put the range all back together turn the gas back on at the appliance shutoff. Locate the gas orifice for that particular burner and hold your thumb or finger over the hole. Turn on the burner and leak test the burner tube connection and where the valve is clamped into the manifold.
Shut the burner back off if the leak test passes and reassemble the stove.
If your burners won't come out of the stove because the screw heads are rusted off (like mine was), you can carefully lift the lid a couple of inches to gain access to the valve. Make sure you don't bend or kink any of the burner tubes.

Straight forward as per instructions. Removed old igniter, replaced and tested new one and it worked. However, the gas oven would not turn of. Valve may be defective. Knob control is not stripped and turned to full stop. Troubleshooting continues. Part(s) and instructions worked perfectly.

- removed the oven unit from the wall
- removed the aluminum backplate to expose the wiring
- Removed both glass wire nuts and disconnected the heating element\
- From the front, I removed both retainer screws and pulled the element wires through.
- In reverse order I reinsalled the new wires and screwed on the heating element.
-I reattached the electrical wiring and rear pane.
- I re-installed the unit into the wall.

Removed grills, oven bottom, heat deflector, and the two igniter mounting screws. Pulled out igniter, removed two wire twist caps and old igniter. Cut off ragged ends of wires coming from the stove side and re-stripped the wire ends. Attached oven side wires to new igniter wires using new twist caps. Reassembled everything in reverse order. Tested oven operation to ensure that the gas ignited promptly. (It did).

well first off I repair commercial HVAC equipment for a major drug company so I think I've done it all.I thought it cant be much different than any burner assembly.I made it harder than it had to be,anyone can do this.I removed lots of unneccessary things.Let me help you only take out the drawer on bottom of stove.so I started on top and worked my way down.save time and open the stove to were the door stops then have faith and give a good yank.this will remove the door,dont be afraid it will go right back on those two hinges easy.now that this is out of the way remove the bottom plate that covers the burner assembly (2 screws)in back pull it out then you see the igniter.as I said before with drawer pulled out remove the 2 1/4"nuts screws holding it up then from bottom.Unplug this stove then remove the 2 places its plugged in to.after you remove this there are 2 screws that hold it into the igniter remove them .cut the wires with enough room to re use the plug ends.strip the wires and use the wire nuts that they provide then put back together with new wires on new igniter then.re attach.put everything back together in the reverse order you took them apart.plug in stove and see the igniter light up again and light stove.do not call repairman you can do this.save your money for you its bad enough you have to buy anything else.

First I disconnected power, then removed two screws from igniter & cliped two wires. Then installed new igniter & with the wire nuts supplied refastened to supply lines in oven.
PartSelect makes repairs quick & easy. It just takes a little smarts on your part.

Remove rear cover. Remove old display. Remove one wire (and place on new board) at a time. Carefully remove faceplate from old board and place on new one. Close everything up and your done. Took 10-15 minutes.

The repair was extremely easy. Just removed the old burners and dropped in the new ones. No tools needed.

Had two burners on the stove that would not light. Had tried cleaning them but they still did not ignite. Replaced both burner heads. Once replaced. they ignited right away and have worked ever since.

0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.

No tools needed, the cap is just held in place with pressure from the wire.