RGB745WEH1WW Hotpoint Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- David from easton, MD
- Parts Used:
- WB28K10025, WB28K10024, WB13K10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set, Wrench (Adjustable), Wrench set
burner tubes both had pin holes in them and the ignighter didnt work
This was a real easy job and a success,of course any repair i do on a gas appliance and when finished It doesnt blow up i consider a success.
Thank you,David Williams
Thank you,David Williams
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Keith from Freeport, IL
- Parts Used:
- WB02K10062
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
I broke the left drawer glide on our oven
I unscrewed to old glide and replaced it then re attached the screw
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janine from Wind Gap, PA
- Parts Used:
- WB16K10055
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burnt burner
Just put it on. Quite proud of myself for figuring out what and how to get the part however! The website was very helpful.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert K from York, PA
- Parts Used:
- WB16K10070
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Needed To Replace Burner
Took longer to open the box.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Hayden, ID
- Parts Used:
- WB16K10035
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Socket set
igniter was bad and tube wasblown
repair was easy enough, but the kit came with female ends and needed mail ends. I had to splice old connecters to new igniter
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lathan from Goodyear, AZ
- Parts Used:
- WB02K10061
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
nylon guide was broke off
took drawer out removed broken guide. It had 1 screw removed it put the new guide in place put screw back in. Put drawer back in stove, It works fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from BENNINGTON, VT
- Parts Used:
- WB27K10355
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Control panel stopped working
Very easy install of done correctly. When you pull range out,watch the gas line and don't pull it out of it's fittings. Two small Phillips head screws on the front panel low to the sides. Then two 5/16 screws on the top back panel and flip it forward. Rest it on the stove and the control panel is facing you. I'm a 30 year Electrician so please take my advice and make a schematic of the wire colors and the NUMBER associated with that color wire. Once that is done remove all wires and also a green ground wire that is under a screw. The new panel may NOT have the exact same configuration but the NUMBER on the terminals will be the same. Plus all color wires to the appropriate terminals and reinstall !! Great job!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from WEBSTER, NY
- Parts Used:
- WB16K10035
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Symtoms: a fluttering noise was heard for a few weeks in the oven prior to it not working at all.
When turning on the oven, I could see the ignitor red hot but it would not ignite the burner. I ordered the pair of new ignitor and burner tube. Upon removal of the burner tube, I saw a large hole in the tube where the center of the ignitor is located, clearly in need of replacement. Unlike some other ovens, the connector on the new ignitor was the exact fit for my oven (Hotpoint RGB745BEA7WH). After access to the tube, the replacement took less than 10 minutes not including watching about 3 youtube videos on how to actually do the replacement prior. You should turn the gas and electric off but ooops, I forgot. I was shocked at how easy this was!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- TERESA from SALTVILLE, VA
- Parts Used:
- WB02K10061
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Drawer glide broken
took nut driver to remove the old and replaced with new. simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Chicago, IL
- Parts Used:
- WB19K10041
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Neither oven nor broiler burner would light, no gas coming from burner.
Remove the warming drawer entirely. Remove all five nuts securing the valve and regulator assembly. Loosen (do not remove the nuts entirely) the burner assembly itself to give some wiggle room above the valve and regulator assembly. Also remove the single screw that holds the "collar" in place just above the gas outlet that services the oven burner. This should provide the margin of room you need to remove the valve and regulator assembly because it's a tight space. Working entirely in this cramped space (the warming drawer) will take time and patience. Don't drop any screws because you might create a whole load of more work for yourself. Loosen the brass nuts holding the gas lines in place. Then you have to maneovre the old equipment out. Just reverse all the steps to install the new equipment. Apply Harvey's to the brass nuts and re-attach the gas lines BEFORE you firmly attach the equipment using the five nuts. Don't tighten the brass parts all the way, just hand tight at first. Re-attach the equipment using the five nuts, then tighten up the brass parts with a wrench. Don't over tighten. Re-secure the screws that hold the burner in place. Then test the equipment. If all good, wait for the oven to cool, then do a final check that all the screws are firmly in place. Voila.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from LITTLE ROCK, AR
- Parts Used:
- WB27K10355
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Oven bake button would not work.
Simple swap and go.Several wires had different locations but every thing was marked well on both panels.Did one wire at a time.Took about 45min from pulling out oven to pushing back in.Just wish I had known about your site years ago.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Trevor from Eldersburg, MD
- Parts Used:
- WB16K10055
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burner on stove not working correctly
Order parts and installed - no tools needed - completed repairs less than 1 minute
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from Corinth, MS
- Parts Used:
- WB28K10025, WB28K10024
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench set
Wife broke gas lines when trying to clean under hood
Removed old line with wrench and attached new line to gas valve first. Then lowered hood to the stop and attached gas line to burners.........very easy and works fine now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charlotte from Rochester, PA
- Parts Used:
- WB16K10035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
oven would glow but the burner would not come on
My son took out the old burner bar and there was a hole burnt right through it. I ordered the part on Weds night and was surprised when we received it so quickly on Fri morning. He had no trouble at all - just removed the old igniter and bar and replaced it with the new one. Nothing needed cut or spliced - perfect match. Now I can bake again!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from REDDING, CT
- Parts Used:
- WB35X37973
- Difficulty Level:
- Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Hard to remove screws & no instructions that a heat shield had to be transferred from old to new
One of the initial two screws for the oven bottom would not budge. Finally used a socket set to loosen it up. Upon taking out the old bottom I turned it over & saw a heat shield attached. I have no idea if you can order a new bottom with a new shield already attached or not, but I had no idea it was there until I took the old part out. Out of the eight screws attaching the shied, four of them were also difficult to loosen up. But in the end the new bottom looks great !
Was this instruction helpful to you?
Thank you for voting!