RB788G*A3 Hotpoint Range - Instructions

Element was easy to remove two screws and unplug it. New element didn't have the same prongs and brace was different. Added ends to plug with screws supplied drilled new holes in oven back for brace. Works fine for a repair by a 65 year old woman.

Open oven door about 3 inches - then holding on the door on either side - pull up and door slides off - put it aside - this is to make it easy for you to work inside oven compartment - at rear of oven where the element goes into the back wall - there are two nuts to remove - I did not have a nut drive so used a pliers (GE could have put slots in the nuts so one would just need a screwdriver) - pull element forward - there are wires attached to the 2 ends of the element - remove with screw driver - element is off - get new part from PartSelect -(and must say pleased with their service) - and reverse above procedure.

Turned off circuit. Unscrewed old element. Connected new element and screwed it in. Worked like a charm. It shipped very quickly. Could not be more satisfied; total repair: $30 and prevented me from buying a new oven; satisfaction: priceless.

First off the part was easy to find on Partselect...

Second point... ordering was easy and shippment was fast thanks to Partselect...

Replacezment was fairly easy useing a Nut driver and a pair of pliers...took about 40 minutes.

Thank you Partselect...

Chuck

Actually you are right, I removed the two screw pulled the element out , disconnected the two wires holding the old element and put the new one on. I spent more time finding out whether or not it would be safe to work on it, being on my own for the first time and always had someone do it for me. I was told as long as the oven was not on it was safe and so I went to work. I was also very impressed at the short time it took to get the part. Three days!!!!!!!!!!!!!!!!!!

1. The infinite switch had several knobs which would fit the switch shaft. Read the directions included with the switch in order to have the shaft fit the proper knob. You can break the shaft with two pairs of pliers. 2. Move the stove away from the wall and unplug it. 3. Remove the 1/4 screws from the back side of the stove and remove the back panel, exposing the switch. 4. Remove the wires one at a time and put them on the new switch. The terminals are L1, L2, P, H1 & H2. The Pilot (p) has a smaller terminal so you don't get it mixed up. Generally L1 is black, L1 is red, P is yellow, H1 and H2 can be blue, brown, yellow, orange or one of these colors striped on a white wire. 5. Remove the old switch from the stove and be sure to save the two mounting screws. 6. Position the new switch so that the side of the switch marked "top" is on top. 7. Install the screws on the new switch and put the knob on it. 8. Carefully test the burner. 9. Unplug the stove and put the back cover on.

Removed back panel. Removed the defective solenoid on its bracket. Replaced it with the new door latch solenoid. This was relatively easy. Replaced the back panel. Tested self cleaning feature. Everything worked fine. I have preformed this same repair once before.

I located and removed 2 sets of hex-head screws under the front lip of the cooktop, then lifted the entire cooktop to access the burner controls. Removed the wires and taped them, and took out the old control after removing 2 phillips head screws. Installed replacement part easily. Only tricky part is that the various shaft adapters don't quite work with my knob. I'll fix it completely with a bit of epoxy and the adapters they sent.

My sons helped with that. They had to use a pliers to remove the old screws (did not have to notches). After that they they removed the element. Then the wires had to be disconnected (after we unplug the oven from the main power source. Then the wires were connected to the new heating unit. We only got one screw in so far will work on getting the second one in when they return tomorrow. I did turn on the oven and it works!!!

Thank you to the nice young man that helped me on the phone.

.....then tested for voltage, had it. Ordered the element through partselect.com and it came in the mail THE NEXT DAY! No kidding! Installed it and the wife is back to her good cooking. All is well, thanks partselect.com. John R., Pompano Beach, Florida

1)Unscrewed the mounting nuts, 2) pulled the heating element out a couple of inches, 3) unscrewed the screws holding the wires in place, 4) removed and tossed the old heating element, 5) placed the new heating element in place, 6) re-screwed the wires to to the element, 7) pushed the heating element back into the wall of the oven, 8) reset the mounting nuts, 9) cleaned up the work area, 10) cranked up the oven and made a pizza. I'm not particularly skilled when it comes to things of this nature, but it was ridiculously easy...

Simple replacement. Price for replacement was excellent. Cheaper than any replacement I priced locally and arrived the day after I ordered.


Thanks!

Two screws to remove the element and two screws for the wire connectors and it was done.

First I turned off the power to the stove,removed oven racks,removed the two screws that held the element in place,pulled unit out a couple inches ,removed the two screws that held the wires in place ,removed element.
Placed new unit where old one went and placed wires in proper order and put together and placed back . turned power back on and WALAA......nothing......apparently that wasnt the problem....Husband baught me a new stove,after 35 years why not.

All other reviews decribed the repare process that I used with no problems. The only reason I took about twenty minutes instead of around 15 minutes was it took me a few minutes to get the correct socket to remove the two small lag screws of the old bake element to free it from the oven wall. I did not have to remove the oven door as it was not a problem in reaching the back of the oven. My range is 25 years old.