RB734*J6 Hotpoint Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Fernando from Auburn, GA
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Burned out oven element
Remove two screws that secure the plate to the oven wall. Pull element out about 6 inches, then remove two screws that attach the element to power lines. Reverse for installation. Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- pierre from virginia Beach, VA
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench set
Electric Burner In oven failed
Parts arrived quickly and install was easy as removing two screws and removing the broken burner. Installed the new and I was done!
Was this instruction helpful to you?
Thank you for voting!
Old and corrosive due to age
After receiving parts, was getting rims unpackaged and removing the old rims, then and installing the new ones. Extremely easy to do. No tools needed
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Courtney from Coon Rapids, IA
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Blown Baking Element
The old part was easily removed with a nut driver, and the new element went right in with a nut driver and screwdriver.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sally from Ravenswood, WV
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Element replaced
It was quite easy-hooked up the wires replaced screws to hold it in place-finished!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- marlene from san rasael, CA
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Element was not working
Removed old element by unbolting two nuts, replaced with new element and two new nuts that were included. Very easy and worked fine.Wish all repair jobs were this easy!Great service with ordering and prompt delivery, too.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patrick from Riverton, WY
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Oven woudn't heat - lower element didn't heat
Took out the two screws that held the old element. Disconnected (unscrewed) the two power cords. Screwed in new power cords and put two screws in new element. Works like a charm. Took longer to get the new element out of the box than to replace it! Thank you!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Tavares, FL
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Lower element burned out
Wasn't sure what to do had a friend come over and it was fixed in less than 15 min. The shipment was really fast and although I only had a partial model number because of age of the unit your search engine found it. Thanks all, my wife is very happy. Your the best!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- harold from burlington, WV
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
baking element broke and would not heat
Shut electric off to range[circuit breaker], removed door and baking racks, removed two screws holding element to back of the oven compartment, pulled the element out to expose the wires, removed screws fastening the wires to the element. Discarded the damaged element and installed the new one in the reverse order. Turned on power and tested. Everything worked fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Naperville, IL
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Oven was uneven in temperature
Removed the bracket holding the element, slid out the element, disconnected it from the leads, replaced it with your part and reassembed. Oven now works like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Teresa from Grand Foks, ND
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
oven element cracked apart, oven would not heat
1-Shut off the breaker
2-Pulled off the oven door for easier access
3-Unscrewed the old element plate
4-Unscrewed the red and black wires from the old element
5-Screwed on the new element to the wires
6-Replaced the screws on the new element plate
7-Turned the power back on
2-Pulled off the oven door for easier access
3-Unscrewed the old element plate
4-Unscrewed the red and black wires from the old element
5-Screwed on the new element to the wires
6-Replaced the screws on the new element plate
7-Turned the power back on
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Melvin from Houghton, MI
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Heating element burned out
Repair was super easy - read the other stories posted. They give more than adequate instruction.
Amazingly helpful website. Found the part, instructions to install, and able to order in less than 20 minutes!
Amazingly helpful website. Found the part, instructions to install, and able to order in less than 20 minutes!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenny from Greenville, MS
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Oven Element would not heat up
I first turn off the 220 power braker to the electric stove. Making sure the stove and element is very cool.
I then removed the two screws that hold the lower baking element in place. Pull gently on the element not to break the wires from the wall of the stove (about 3 to 4 inches).
I than unscrewed the right and left wire attached to the element with the nut driver. (This old element was attached with small nut screws. The new one has screws that use a screw driver). Keeping the wires apart, I removed the old element and replace it with the new element part.
In replacing the new element, facing the stove I connected the black wires to the left side (my left hand) and the white wire to the right side (my right hand) with the new screws using a screw driver. REMEMBER TO REPLACE THE WIRES BACK THE WAY THEY CAME OFF WHEN THE STOVE WAS WORKING PROPERTLY. Attach the element back to the stove and turn the breaker on. Easy to do job.
I then removed the two screws that hold the lower baking element in place. Pull gently on the element not to break the wires from the wall of the stove (about 3 to 4 inches).
I than unscrewed the right and left wire attached to the element with the nut driver. (This old element was attached with small nut screws. The new one has screws that use a screw driver). Keeping the wires apart, I removed the old element and replace it with the new element part.
In replacing the new element, facing the stove I connected the black wires to the left side (my left hand) and the white wire to the right side (my right hand) with the new screws using a screw driver. REMEMBER TO REPLACE THE WIRES BACK THE WAY THEY CAME OFF WHEN THE STOVE WAS WORKING PROPERTLY. Attach the element back to the stove and turn the breaker on. Easy to do job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Elkton, VA
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
bottom element was burnt out
removed 2 screws that hold the element in place, then pulled element out took 2 more screws out and reversed proc. I couldn't have had a better rep to help me find the right part. Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary Grace from Nashville, TN
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The baking element burned out.
I had a friend of mine who came to my home equipped with screwdrivers and flashlight. After turning off the electricity at the fuse box he removed the oven door (for easier access),removed the screws,pulled out the existing element far enough to disconnect the wires, placed the new one into place, connected the wires, screwed the new one into place
turned the power back on, turned on the oven and after about 15 seconds, the element began to turn from a dark gray to a light color beginning to turn orange.
turned the power back on, turned on the oven and after about 15 seconds, the element began to turn from a dark gray to a light color beginning to turn orange.
Was this instruction helpful to you?
Thank you for voting!