RB734*J2 Hotpoint Range - Instructions

I first removed the two hex head screws, pulled the element slowly forward about four to five inches and disconected the two wires on the old element.
I removed the old element and attached the wires to the new element. I then slowly pushed it back into the rear wall of the oven, carefull not to disturb the insulation around the opening and replaced the two screws that hold the element to the back wall of the oven. It was easy enough to do, even for a woman. I turned on the oven and it worked great. No problems so far.

Had to take back panel off of the inside of the oven to get to the screws to remove the old element and attache the new. Removed the two screws to remove the old, pulled it out unattached the wires and attached the new one.

The hardest part was working in the oven.

Turn off power
Open Oven Door, remove racks
Remove two mounting screws with nut driver.
Slide the element out to expose the wire connections.
Remove the screws and pull the element out.
Place the new element in oven.
Clamp on to each of the terminals with vice grips to keep from bending the element and install the screws.
Slide the element back into place and put the two mounting screws back in.

Put the racks back in and turn on the power and test. You may get a little smoke off the new coil.

Like I said the hardest part is leaning into the oven to attach the screws, do not sit on the oven door.

Could not believe how fast the part shipped. 2 days and it was here. All it took was using a nut driver to remove 4 screws and then put the new one in.

My 17 year old son and I (his mom) replaced the oven element in less than 15 minutes!!! It was so easy. We first unplugged the stove since I didn't want to go and shut off the circuit breaker in the dark!! We then removed the two screws that hold the element in place and started to pulled out the element. It was actually corroding in my hands as I pulled it out. We disconnected the wires and then put in the new element by reconnecting the wires, pushing the connections back in and replacing the two screws that hold the element in. The oven heated right up!!! What a savings to do it yourself and not have a repairman charge us extra to do a 10 minute job!! Thank you Part Select for your fast service. I will definitely look here before I shop anywhere else. Thanks,

Four screws and two wires.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Then I replaced it with the new element that took only two days to arrive and that was without paying extra express shipping fees. It couldn't have been easier. I didn't even wait for my husband to come home and install it. I had an oven-baked meal ready when he got home. I was very satisfied.

Remove two screws that secure the plate to the oven wall. Pull element out about 6 inches, then remove two screws that attach the element to power lines. Reverse for installation. Very easy.

Replaced old bake element with new one. 4 small screws/nuts. From order to fix was 3 days. My wife was impressed.

Went on line to find the part number and ordered the part. It came in the mail two days later and I installed in about five minutes.

Very easy to replace. Oven works like new again. If you have even the most basic visual and mechanical ability, you will be fine to do this on your own. Total repair time for me was less than 5 minutes. The part was an exact fit!

Took the old one out, measured it, ordered the appropriate size, intalled the new one.

My daughter and I turned off the breaker to the range and removed the old element and replaced it with the new one. My husband came home and took over after we had done almost everything ourselves!!

Unpluged Stove, Unscrewed the wires attached to the Element in the back of stove after I removed the cover. Removed the two screws that held the Element at the back of the oven compartment. Then replaced the Element with the new one and put back the screws, the wires and the cover in the same sequence iI took it apart. Plugged it back in works like new!

My husband removed the screws holding the element, disconnected the wires from the old element. He then reattached the wires to the new element, putting it back into place, tightened the screws, and we were cooking again. The shipping service was GREAT! I ordered the part on-line and it arrived next day! Thanks!