RB636*A1 Hotpoint Range - Instructions

First I removed the two screws that hold the element in place. I pulled the element out and disconnected the two wires that hold it in place. I reversed the process for the new element and viola! The oven works just great. The element actually arrived a day earlier than expected. Thanks Parts Select!

My husband helped me pull the range out from the wall to unplug it, I removed the screws on the hinged bracket, pulled the wiring out a couple of inches and removed the screws attaching the element to the wiring. Then I reversed the process. Easy as pie. The most time consuming part was unplugging the range, but as it is 220v (can kill you) I consider it a nesessary step. The best part was the price and availability. I ordered the part on Sunday p.m. and got it on Tuesday p.m. at half the price quoted by a national chain.

The complete repair was quick, easy, and painless. Not only did my item show up sooner than I thought the whole replacement took only 15 minutes, tops, to complete. I even had my 18 months old daughter helping too.

First and foremost I turned off the power to the oven by tripping the circuit breaker in the basement. Then verifying that the oven or stove top did not work to insure that the correct circuit breaker was tripped.

Then I removed the two mounting bolts on the support plate, that holds the element in place, from the rear wall of the oven. Then slide out the element just far enough to gain access to the wires that are attached to the element, about 3-6 inches. Carefully removed the two wires from the element with a screwdriver, noticing how flexible the ends of the element were. Removed the old element out of the oven. Placed the new element into the oven and then reattached the two wires to the new element terminals, being careful not to bend the ends of the element too much, very flexible!! Slide the element back into place and then reattached the mounting bolts. Turned all power back on to the stove and then turned the oven on and presto!, my oven is fully functional again.

The bake element was completely missing from the stove. There were two wires sticking out of the back of the oven, one with a terminal on the end and the other with the insulation still on and no bare wire showing/ The right side mounting screw was there..

The left mounting screw hole on the oven had been drilled out oversized, so I drilled another hole in the mounting plate above the original., after attaching the element with a single screw.

I removed the one screw, removed the bake element and pulled the electrical wire without the terminal end. Next, I put a terminal on the wire and attached the wires to the element. Finally I installed the element with the two screw into the rear of the oven.

Unfortunately the element didn't work, so my next step is to trace the wiring and determine if a switch or thermostat might be faulty. I have checked the continuity of the wires from the bake element to the thermostat.

More in chaper two..

Before ordering the new part, made sure the problem was the burner and not the wiring in this very old stove by putting an ohmmeter on the terminals of the burner after removing it. Since it showed no conductivity, the burner was bad (could have put the voltmeter on the wires and turned on the power to ensure power was coming in......but did not want to mess with 240 volt/high amperage. With power off at the breaker, installed new burner. One caution... since the wire on the burner terminals is pretty soft, don't bend them by putting too much torque on the screws. This turned out to be my only problem.....I had to clean up the screws and work them through the copper terminals with the burner outside the oven before attempting to screw them on the wire connectors in the oven. Not a big problem, but if you bend the terminals too much when you install the burner in the oven, you run the risk of shorting them together, or breaking one. And that would be a big problem.

Removed 2 screws (with 1/4" nut driver) on bracket holding heat element at back of oven. Pull element forward to expose the 2 wires connected to element, remove screws on wire corrections with flat head screw driver. Remove element from oven......Reverse the steps to install new heat element.....very easy job....except I cleaned the oven while I had the element out of the oven.

The repair was pretty easy. I unplugged the stove and took the 2 screws out that secured the element into the back of the stove. I then used a pair of needle nosed pliers to pull the wires off the element that wasn't working and then attached the wires to the new element. I then put the screws back in place securing the element to the stove and it was done. It took me about 5 mintues and the element worked immediately.

unscrew two screws pull the old element out put in new one and screw back in . We had to wire it direct because our oven had quick connect connectors and this part did not. But it was no big deal and didn't take any time to fix.

The part arrived ahead of time by mail. I removed the old coil, very simple,, I installed the new one just as easy , Turned on oven and it worked prefectly , its a very simple procedure, thank you

Removed screws that hold element in place. Disconnected the two electrical leads. Put the new element in place, hooked up the two leads and installed the the screws that hold the element in place.

Because of the age of the oven it took a little time to loosen the screws that held the element in. Once the screws were removed it was a matter of pulling the element out about 3 inches and disconnected the two wires, then it was a matter of repeating the steps in reverse. Very quick and easy

First I shut off the range breaker in the main electrical panel. I slid the oven door off for easy access to the back of the oven. I loosened the two hex head screws holding the element to the oven wall. I pulled the element forward to reveal the two hex head screws holding the wires to the element and removed the old element. I attached the wires to the new element with the hex head screws, fastened the element to the oven wall, slid the oven door back on, and flipped on the breaker. I gathered up my tools and left the apartment. It took me longer to get to the apartment and back than it did to do the repair. PartSelect.com got the part to me within two days of my order, and for six dollars in shipping that's great.. PartSelect.com has been added to my internet bookmark.

This was quite an easy fix once I got the correct part. It was my own fault for ordering what I thought went with my oven. I didn't expect to be able to even find a new heating element because the stove is almost 40 years old. Except for that one part it works just fine. It took me about 20 minutes to do the repair. I unplugged the stove, unscrewed the 2 screws holding the element to the back of the stove, pulled it out far enough to unscrew the 2 screws attached to the wires, screwed the new part to the wires, screwed the whole unit back onto the back of the stove and plugged it back in. It works great. Moving the stove away from the wall was more difficult than installing the new part. It couldn't have been easier and it was a lot less expensive than buying a new stove. Also, the customer service people I spoke to were very friendly and helpful and there was no problem returning the incorrect part. I would recommend this company to anyone who asks.

Removed the screws. Pulled out the element and disconnected the wires. Attached the wires from the new heating element and screwed it in.

I used a philip screw driver to remove two screws which enable me to pull the wires out about three inches from the back of the oven and replaced it with the new one after disconnecting the wires from the grill. The hardest thing was the limited space.