RB528*A1 Hotpoint Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Sarah from San Andreas, CA
- Parts Used:
- WB31X5013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Original trim ring did not fit
I had an appliance guy replace a burner(Calrod unit)on my 47 year-old GE range, but he didn't tell me that the original trim ring wouldn't fit. I decided to look up on PartSelect to see if I could get one to fit the new burner, and I did! Fits perfectly......no tools needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- brian from temple, TX
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
burned/blow out element
pull oven from wall,unplugged.removed back with small hex or screw driver . opened oven slide element into slot screwed two screws in, pushed in two connectipn on back .replaced cover on back .plugged in and put oven back in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Erwin from minneapolis, MN
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
element was broken
replace old one with new one thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eunice from North Providence, RI
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
broken bake element
1. remove two nuts on rear of oven wall.2. remove 2 screws holding connection to element. 3. attach element to oven wires w/ 2 screws. 4. reinstaill 2 nuts to oven wall. 5. Test oven.Make sure power supply is disconnected @ electrical box!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cindy from VACAVILLE, CA
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burned out lower element
Shut off breaker to oven. Removed two screws holding the element. Removed two wires attached. Cut back old wires and crimped on two new eyelet terminals. Screwed wires onto element and reattached. Turned breaker on and tested. Works great. Any girl can do it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff from Cody, WY
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
bake element broken and bubbled
removed two screws with nutdriver, removed two screws attatched to element. reversed procedure. this took less than 15 minutes. "remember to turn turn off power" Jeff
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Albert D from Fort Worth, TX
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
bake heating element burned out
removed the old element, inserted the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Milt from Manchester, CT
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
bake element burned out
A socket set was used to remove the old element. New element was installed with a slotted screw driver and socket set. It took 15 minutes from start to finish to complete the removal and installation. Element tested OK. The bake elment was delivered overnite by Fedx.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lorraine from El Campo, TX
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Old bake element burned out
First, I turned off the power at the breaker box. Then, I removed the 2 screws attaching the bake element to the back wall of the oven. Next, I pulled the element out a few inches and removed the screws holding the element to the wires at the rear of the oven. Finally, I reattached the new element to the wires with the screws and then reattached the element plate to the rear wall of the oven. I turned the power back on at the breaker box, and tried the new element. It worked! Also, shipping was real fast, like 2 days from the time I placed the order to receiving the element.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Samuel from Beavercreek, OH
- Parts Used:
- WB44X5099
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Element burned out
Simply removed two screws to detach element from oven wall, removed two terminal wires then reversed the procedure to install the new element.
Was this instruction helpful to you?
Thank you for voting!