RB734*A6 Hotpoint Range - Instructions

Removed 2 screws that hold the element in place. I then pulled the element out 3-4 inches and noticed 3 wires attached. (had expected 2). Disconeccted the 3 wires and renoved old element.. Reversed process with new element, and reattached wires as I found them. Inserted element and inserted holding screws for new element. Ran through self-cleaning cycle. Works great. A written warning about the wires in the box would have been comforting.

Repair was super easy - read the other stories posted. They give more than adequate instruction.

Amazingly helpful website. Found the part, instructions to install, and able to order in less than 20 minutes!

I first turn off the 220 power braker to the electric stove. Making sure the stove and element is very cool.

I then removed the two screws that hold the lower baking element in place. Pull gently on the element not to break the wires from the wall of the stove (about 3 to 4 inches).

I than unscrewed the right and left wire attached to the element with the nut driver. (This old element was attached with small nut screws. The new one has screws that use a screw driver). Keeping the wires apart, I removed the old element and replace it with the new element part.

In replacing the new element, facing the stove I connected the black wires to the left side (my left hand) and the white wire to the right side (my right hand) with the new screws using a screw driver. REMEMBER TO REPLACE THE WIRES BACK THE WAY THEY CAME OFF WHEN THE STOVE WAS WORKING PROPERTLY. Attach the element back to the stove and turn the breaker on. Easy to do job.

removed 2 screws that hold the element in place, then pulled element out took 2 more screws out and reversed proc. I couldn't have had a better rep to help me find the right part. Thank you

I had a friend of mine who came to my home equipped with screwdrivers and flashlight. After turning off the electricity at the fuse box he removed the oven door (for easier access),removed the screws,pulled out the existing element far enough to disconnect the wires, placed the new one into place, connected the wires, screwed the new one into place
turned the power back on, turned on the oven and after about 15 seconds, the element began to turn from a dark gray to a light color beginning to turn orange.

I noticed two screws held the heating element in place. I removed the screws. Pulled the heating element out a few inches. Removed the two additional screws which held the two wires on.

To install the new element, I used the two new screws that came with the element to attach the wires to the element. Insert the element into position and attached the element to the rear wall with the two screws which were first removed.

turned off the electric at the breaker box.
removed the door, and racks. unscrewed two bolts, pulled out and unscrewed the leads. reattached the leads, and pushed in and reattached the element.
put the racks and door back on. turned on the electric and then tested the oven. easy!!

1-Shut off the breaker
2-Pulled off the oven door for easier access
3-Unscrewed the old element plate
4-Unscrewed the red and black wires from the old element
5-Screwed on the new element to the wires
6-Replaced the screws on the new element plate
7-Turned the power back on

I am a CPA and not real handy at all. But I was able to remove the old element and install the new element in less then 15 minutes. It burned out on Saturday, I ordered new one FED-ex to speed up- received new one, on Tuesday. Very quick, and this was last week, the week prior to Thanksgiving- so my wife really needed our oven. Perfect fit. And I am not related to this company in any way, nor was I paid anything to say this, just happy this worked- or we'd be spending a lot more money.

Too easy to describe. Just lifted out the old rings and popped in the new ones. PartSelect is my go-to source for appliance parts both for my home and my job as maintenance man for residential group homes in my area. Website is easy to use, prices are good, shipping is always surprisingly fast. Thank you.

Removed the bracket holding the element, slid out the element, disconnected it from the leads, replaced it with your part and reassembed. Oven now works like new.

It only took 15 minutes and a nut driver to replace.The part was $22,well worth keeping my oven going for a few more yaers

Removed bolts from fixing plate, pulled out existing element, unscrewed wire connectors and installed new element in reverse order of removal. This is an old stove from the 60's or 70's so I was glad to get a replacement part and fit it myself so easily.

I first looked at a video PartSelect had done on replacing the bake element in a stove. I disconnected the stove's power plug from the wall, removed the baking shelves, and removed screws holding the cover plate for the old bake element with a nutdriver. I removed the two screws holding the power wires to the bake element and replaced the bake element with the new element purchased from PartSelect. The cover plate was repositioned by using the nutdrive to tighten the cover plate screws. After reinstalling the bake shelves and plugging the oven back in, the repair was finished.

I have some electrical experience. It was simple to remove and install. You just have to pay attention to wiring upon removal and installation.