RGB746HEH1CT Hotpoint Range - Instructions

1) Turn off power at circuit breaker panel
2) Slide out Range from wall
3) Unplug Range
4) Remove back panel and unplug electrical connections to socket
5) From front of oven, remove glass cover over old oven light bulb and remove flange that holds socket and bulb
6) Remove old socket from mounting flange and discard.
7) Place new socket into mounting flange
8) Screw mounting flange and new socket into the oven from front. Reattach electrical connections from back.
9) Screw in new light bulb from front
10) Replace existing glass cover over new light bulb and snap wire holder in place
11) Replace back panel
11) Plug in range
12) Slide range back to original position
13) Turn on power
Works like a charm! Thanks for having the parts after 30 years!

First I tested oven sensor which checked o k. I then made a diagram of the electrical wireing to the oven control. I disconnected wireing and removed the control then with sharp knife I removed touch control pad. I placed th touch pad on the new panel and installed panel and connected wiring. Pluged into wall rec and test oven which checked o k .

I removed the four burners and the two metal tops, easy as one, two, three!!

This was a real easy job and a success,of course any repair i do on a gas appliance and when finished It doesnt blow up i consider a success.
Thank you,David Williams

Not a repair - just a replacement. Very easy. Just remove the grates, lift out the drip pans, replace with the new drip pans, and replace the grates. As the size of the holes vary you just have to make sure that they are lined up correctly. I was delighted to find that replacements were available for a range I've had for 14 years. The range itself still works great. Thank you for your promptness in sending the replacements. I highly recommend your service.

repair was easy enough, but the kit came with female ends and needed mail ends. I had to splice old connecters to new igniter

Took longer to open the box.

I unscrewed to old glide and replaced it then re attached the screw

Just put it on. Quite proud of myself for figuring out what and how to get the part however! The website was very helpful.

took drawer out removed broken guide. It had 1 screw removed it put the new guide in place put screw back in. Put drawer back in stove, It works fine.

Very easy install of done correctly. When you pull range out,watch the gas line and don't pull it out of it's fittings. Two small Phillips head screws on the front panel low to the sides. Then two 5/16 screws on the top back panel and flip it forward. Rest it on the stove and the control panel is facing you. I'm a 30 year Electrician so please take my advice and make a schematic of the wire colors and the NUMBER associated with that color wire. Once that is done remove all wires and also a green ground wire that is under a screw. The new panel may NOT have the exact same configuration but the NUMBER on the terminals will be the same. Plus all color wires to the appropriate terminals and reinstall !! Great job!!

My son took out the old burner bar and there was a hole burnt right through it. I ordered the part on Weds night and was surprised when we received it so quickly on Fri morning. He had no trouble at all - just removed the old igniter and bar and replaced it with the new one. Nothing needed cut or spliced - perfect match. Now I can bake again!!!

When turning on the oven, I could see the ignitor red hot but it would not ignite the burner. I ordered the pair of new ignitor and burner tube. Upon removal of the burner tube, I saw a large hole in the tube where the center of the ignitor is located, clearly in need of replacement. Unlike some other ovens, the connector on the new ignitor was the exact fit for my oven (Hotpoint RGB745BEA7WH). After access to the tube, the replacement took less than 10 minutes not including watching about 3 youtube videos on how to actually do the replacement prior. You should turn the gas and electric off but ooops, I forgot. I was shocked at how easy this was!

Remove the warming drawer entirely. Remove all five nuts securing the valve and regulator assembly. Loosen (do not remove the nuts entirely) the burner assembly itself to give some wiggle room above the valve and regulator assembly. Also remove the single screw that holds the "collar" in place just above the gas outlet that services the oven burner. This should provide the margin of room you need to remove the valve and regulator assembly because it's a tight space. Working entirely in this cramped space (the warming drawer) will take time and patience. Don't drop any screws because you might create a whole load of more work for yourself. Loosen the brass nuts holding the gas lines in place. Then you have to maneovre the old equipment out. Just reverse all the steps to install the new equipment. Apply Harvey's to the brass nuts and re-attach the gas lines BEFORE you firmly attach the equipment using the five nuts. Don't tighten the brass parts all the way, just hand tight at first. Re-attach the equipment using the five nuts, then tighten up the brass parts with a wrench. Don't over tighten. Re-secure the screws that hold the burner in place. Then test the equipment. If all good, wait for the oven to cool, then do a final check that all the screws are firmly in place. Voila.

Removed old line with wrench and attached new line to gas valve first. Then lowered hood to the stop and attached gas line to burners.........very easy and works fine now.