RB525GS2 Hotpoint Range - Instructions

Moved stove from wall, unplug the stove from the wall outlet, remove the oven racks, unscrew the plate against the oven wall supporting the element with a small adjustable wrench, pull out the element slowly without tearing the insulation & stretching the two wires, unscrew with a phillips screwdriver each wire with care, as a precautionary measurement: do not make contact with the other wire and any other part of the stove, even though it was still unpluged. Install the new element in reverse procedure...turn on Bake Element on low temperature..when it glows when hot..ready to go.

I was very impressed how quickly the package arrived. I would you your company again. I found you with a google search.

shut off electricity to the range, removed the screws holding the element in place, pulled the element out as far as it would go, removed the screws holding the wires in place, tossed the old element, attached the wires to the new element, pushed the element back into place and reattached the screws holding the element in place. Turned the electricity back on and the oven heated right up.

Also, the part arrived the day after I ordered it. Great Price & Great Service.

I lifted out the burners and took out the old drip pans ans then replaced the burners. However the 8 inch pans were bigger than the old ones and they do not fit properly. They are sitting on top of the stove and not inserted like they should be. I will have to look elsewhere to find ones that fit.

No repair necessary, but the service was excellent!

Easiest thing I've done. Shut off breaker. Unplug range. Pull out from wall (because this is a good time to remove the back, clean under and around the unit, check out the insulation and electrical contacts....or skip it, whatever). Open oven. Remove door (while ajar, pull up). Remove racks. Unscrew mounting plate from back interior wall. Set screws aside. Gently pull element forward until the leads and wires come through the insulation. Remove any strands of insulation that stuck to the leads and connectors. Unscrew leads. Keep left wire to the left and right wire to the right. DO NOT CROSS. Set screws aside. Discard old element. (This is a good time to clean your oven, if you haven't in a while.) If you cleaned oven, wait until dry. Position new element, feet down, in bottom of oven. Position left wire on left connector. Screw tightly BUT DO NOT BEND LEAD. IF YOU BEND IT, THEN DO NOT BEND IT BACK. CALL A PROFESSIONAL. Position right wire on right connector. Screw tightly BUT DO NOT BEND. IF YOU BEND IT, THEN DO NOT BEND IT BACK. CALL A PROFESSIONAL. Do not leave screws loose. Connection must be tight. Fire hazard, otherwise. If you bent nothing, then gently push element back through insulation until mounting plate is flush. Screw into position. Replace racks. Replace door. If you decide to check insulation and other leads, now is the time. I checked mine and it's a good thing I did.... Unscrew back plate of oven, keeping screws in order. Remove plate. Check that your new element and insulation aren't bunched up or otherwise in a hazardous state. You may notice burned or greasy insulation. You may see burned leads on light receptacle and broil element. If you do, then replace them, too. When finished with everything, replace back plate. Put range back into position, ensuring level and plumb. Plug in. Turn on breaker. Pat yourself on the back. You just saved $100-$250, depending on where you live.

1. Make sure electricity is off!
2. Remove 2 screws at rear of oven where the bake element is attached.
3. Pull out far enough to remove the 2 screws where the wires attach.
4. Lift out the old element and set the new one in.
5. Reattach the wires.
6. Reattach the element to the rear of the stove.
7. Turn electricity back on.

took the old one out and dropped the new one in, replaced the electric burner and done

thw worse part was paying as much for s&h as i did for the part itself

Removed old surface burners and replaced them by plugging in the new surface burners. Now they work GREAT! Parts ordered and received with-in 3 business days. Fed EX delivered parts in good order very quickly. We recommend PartSelect.com

Replace part an wires

Unplug coil, remove pan - place new pan, plug in new element and bingo. Took approximately 30 seconds!

Partselect made this job a breeze. Due to the user friendly process to order and receive the part. I repaired the stove after turning off the breaker in the main box. There were two screws that held the baking unit in place, removed them and then replaced with new unit.

Surface element easily unplugged and removed, drip pans lifted out, New drip pans inserted, New 8" surface element and present 6" surface elements Inserted and plugged in.

OK, I put the drip pan under the burner. Without a single problem.

Removed existing surface element and replaced with new element.

P.S.

Part Select service was excellent.