RS776G*01 Hotpoint Range - Instructions

First I turned the circuit breaker off, then I removed the two screws with a nut driver, that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires with a straight scewdriver.

Reversed the the above process to install new element.

Oven was 27 years old.

Repaired and operational in less than 15 min.

Opened Breaker box
Threw oven switch
Removed two screws on element plate
Pulled element out 3 inch and removed two screws holding wires.
Ordered element on Tue.
Received element on Thur.
Reconnected screws on wires and plate
Threw oven breaker
Baked a cake

Super easy, 1 2 3 steps and your done. Make sure to turn power off, remove two screws off of back plate. Remove two screws on wire connectors. Throw old element away and connect both wires to new element and screw back into place. Turn power back on and start cooking.

very easy--cut power supply 2 screws then 2 more on element quick and easy

first i removed two screws pulled that hold the element in then pulled element out about 3 inche disconnected the two wires now hot meals thanks

Replaced old drip bowls with the new ones. Very simple, no tools required.

Undid two screws to pull the element out, and another two to unhook it from the wires. Reverse procedure with the new element and baked some muffins. The hardest part about this repair was getting the part. I typo'd my shipping address and had to knock on a neighbor's door!

pull oven from wall,unplugged.removed back with small hex or screw driver . opened oven slide element into slot screwed two screws in, pushed in two connectipn on back .replaced cover on back .plugged in and put oven back in place.

Attached the screws and was done. Unbelievable! Ordered the part at 10 am and was delivered at 11 am next day. Great shipping!

got new part delivered two days after ordering. I turned off breaker, used a 1/4" wrench to remove the fasteners holding the heating element to the back inside wall of the oven. used screw drivers (one Phillips and one flathead) to remove the screws holding the heating element to the wires. ensure you pull the wires slight out (easily) to ensure they don't pull back into the oven wall. unplug the element from the wires, install new element in reverse fashion and voila, done.

Removed the element and put in a new one. Screw mounted interface to 230 mains involved removing two screws in oven wall and two connecting the main wires. Screws were provided with element. Effortless replacement saved an expensive house call and/or oven replacement. Oven is 44 years old and Parts Select had an original replacement part here in 4 days at new years. Part was only $18.45. Parts Select rocks!

Ordered new element (super-easy to select the right one at this site!). Turned off stove breakers. Removed two screws holding mounting hinge plate with nutdriver. Detached wires with regular screwdriver. Attached wires to new element lugs with screwdriver, using furnished new screws. Reinstalled element hinged mounting plate with screws and nutdriver. Only difficulty is 1) working bent over inside the oven because the wires are short, and 2) wire screws are regular, not Philips, with shallow slots so screwdriver slips out frequently.

Turned the power off. Loosened two screws to take the element out. Loosened two more srews to disconnect the element itself from the power. This job was easy squeezy. Within 15 minutes flat I was back on the couch watching old Seinfeld reruns. Two thumbs up for the peeps at Part Select.

Took off oven door, removed screws, disconnected wires took out damaged part. Reversed the order. Job complete!

Turned off breaker for oven, removed baking (lower) element, searched website to match up size, shape, and connector-type of replacement part. Placed order and received two days later. Mounted new part in 10 minutes, turned on breaker, and immediately baked fries for children. No problem. Much cheaper and easier than replacing entire built-in oven.