RK747G*T3 Hotpoint Range - Instructions

I read your website repair testimonials by previous customers and used that advise to do the job. I liked the suggestion to use something to attach to the unattached wires so they don't slip back into the unit. I used two clothespins. I had one stubborn electrical connection to disconnect so it took a little longer -about 30 minutes. But it was a simple job to do and my oven works fine again. The item was delivered timely from the order date and packaged well. Thank-you!

Turn off circuit breaker. Release bake element from back of oven with a phillips head screwdriver. Remove bake element from heating wires with an adjustable wrench. 1/4 nutdriver was a little to big large for the old screw. Do not allow wires to fall back into the installation. Reverse the procedures for installing the new bake element. Most difficult part of the repair is having old eyes and not being able to focus on the work site which is about 12- 14 inches from your eyes. Young people with good eyes no problem. Oven heats like a new unit.

having read instructions from previous PartSelect users it was a snap. Nutdriveer, and screw driver were the only tools needed. This was a wall oven and the most difficulty I had was getting to the nuts with the door open. I really didn't want to take off the door.

My petite 69 yr old wife replace element in about 15 minutes with no problem..Also product arrived within a short time frame and your online instructions were accurate. Thanks

On thanksgiving day, as we were pre-heating the oven, electric sizzle, sparks and a little flame comes from our 24 year old oven. We were able to get dinner on the table and that evening I went looking for what I thought was going to be a difficult to find part. But I found the part on partselect. I ordered that evening and got it on saturday. Installation was a snap. The most difficult part was the nuts holding the wires were stuck on from time and heat and I worried about the wire from the small plate to the coil might break. A little wd-40 and a few minutes and they popped right off and right back on. Works great now.

Removed the 2 screws that held element in place. Pulled the element out about 2 inches to disconect the wires. I then reattached the new element and replaced the screws holding the element in place.

My Husband did the repair while I wasn't home. He didn't bother to shut off the power even though he should have. He didn't electicute himself or burn down the house and the oven works great so I guess it was a success!

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and made sure that there was no power feeding the element. Next I disconnected the two wires that power the element. I then removed the old element and replaced it with the new element. Tightened the screws but had to be careful on the second one and hold with plier as the first one bent a little as it was being tightened. Slid the element back after the connection screws were tightened and tightened the mounting screws. Reenergized and tested. The job went well - easier than expected...

Removed the coverplate screws, slid the element outward, and removed the wire connecting screws. Positioned the new element to reconnect the wires, and discovered this isn't easy to see with trifocals. Succeeded after several failed attempts. Slid the new element into position, and reattached the cover plate.

First I turned the power off to the oven. Then I tried to take out the nuts holding in the element. One nut came off easily, the other one was rusted on, I had to use wd40 to loosen it. The project was easy once I got that nut off. I pulled out the element, which is connected to two wires. I took those screws out, connected the new element to the wires, re-attached the screws, pushed it back in, attached the nuts that hold the element in the oven. Then I turned the power back on and the oven works like a charm. I installed it the day I got it. I was surprised how quickly it was shipped to my house. I am so glad I repaired the oven, a new one would have cost over $800, I bought the element for less than $30, including shipping! It also sets a good example for my daughter. It taught her that her mom can repair things too, it's not just something men can do!

Removed the bad part. There were 4 screws,
Found part on the internet.
When part arrived I installed it using the screws that I removed when I took out the bad part.

Replacing the electric oven element was easy. It took about 20 minutes and all you need is a screwdriver and a pair of pliers. What you have to do first, turn the power to the oven OFF. Remove the original element carefully observing how
it was installed and install the new element in the same order.
I have used Parts Select a couple of times in the past years and the delivery came quicly without any problems.

Spyro.

Turn circuit breaker off.
Two screws detached the unit.
Another two screws to disconnect the wires. Reversed above operation for installation.
Turn circuit breaker on.
All fixed!

P.S. Shipping was very fast.

First turned power off for oven circuit at the breaker box then removed two screws that hold element in place. Pulled element out, tested for current, then removed two screws holding wires to element. Took old element from oven and inserted new element. Reattached wires with screws provided, and pushed element into opening. Replaced two screws securing element to back wall of oven. Turned the circuit breaker back on then checked to ensure the oven was working.

1. Turned the electricity off at the fuse box.
2. Took out the two metal screws holding the element to the oven back.
3. Unscrewed the screws holding the element coil, pulled the element out some and disconnected the two wires.
4. Replaced the old element with the new one.