RB6364A1 Hotpoint Range - Instructions

The complete repair was quick, easy, and painless. Not only did my item show up sooner than I thought the whole replacement took only 15 minutes, tops, to complete. I even had my 18 months old daughter helping too.

First and foremost I turned off the power to the oven by tripping the circuit breaker in the basement. Then verifying that the oven or stove top did not work to insure that the correct circuit breaker was tripped.

Then I removed the two mounting bolts on the support plate, that holds the element in place, from the rear wall of the oven. Then slide out the element just far enough to gain access to the wires that are attached to the element, about 3-6 inches. Carefully removed the two wires from the element with a screwdriver, noticing how flexible the ends of the element were. Removed the old element out of the oven. Placed the new element into the oven and then reattached the two wires to the new element terminals, being careful not to bend the ends of the element too much, very flexible!! Slide the element back into place and then reattached the mounting bolts. Turned all power back on to the stove and then turned the oven on and presto!, my oven is fully functional again.

First I removed the 2 mounting screws that mount the element to the back wall in the oven, then pulled the element out about 4 to 5 inches, then removed the 2 screws attaching the wires to the element, then reversed the process to instal the new element. The only tool reguired was a 1/4 inch nut driver. Did the job in about 5 Minutes. The replacement fit and works perfectly.

I removed the screws holding the element in place. I pulled the element out from the back of the oven about 3" and then disconnected the two wires. I then reattached the two wires to the new element and pushed the element back flush with the rear of the oven. I then rescrewed the two screws that hold the element in place. That was all there was to it.. Very easy. I am 54 years old and have never done this before.. So if I can do it so can you....

Customer service is great. Fast shipping. Great communication. I have them bookmarked from a previous order. Same good service as the first time. Thank you.

Pulled range out from the wall. Unplugged cord from outlet. Removed old knob, removed two phillips screws a very top of chrome trim, removed six nut-head screws from back to reveal the switches...removed two set screws from the front at knob base. Visually checked to make sure wiring post of new switch matched the old one. There was enough slack in the wiring to remove one wire at a time and connect it to the new switch in its appropriate place. Put new switch in the panel and secured with the two set screws. Select the bushing that would take up the slack for the old knob to fit on the new switch stem. Held new stem at its base with pliers and used another pair of pliers to snap the stem at appropriate length. (The new stem could not be broken off short enough to have the knob as flush to the panel as the other knobs...this was the only negative factor in the repair) Replaced nut-head screws and phillips screws. I was especially pleased with the quick delivery of the part...even without special shipping rates I received the part in less than 18 hours from the time I ordered it online!

lift eye slide in bowl and trim ring, put the eye back down,

First I removed the two screws that hold the element in place. I pulled the element out and disconnected the two wires that hold it in place. I reversed the process for the new element and viola! The oven works just great. The element actually arrived a day earlier than expected. Thanks Parts Select!

My husband helped me pull the range out from the wall to unplug it, I removed the screws on the hinged bracket, pulled the wiring out a couple of inches and removed the screws attaching the element to the wiring. Then I reversed the process. Easy as pie. The most time consuming part was unplugging the range, but as it is 220v (can kill you) I consider it a nesessary step. The best part was the price and availability. I ordered the part on Sunday p.m. and got it on Tuesday p.m. at half the price quoted by a national chain.

removed the old heating element which had about two screws and two connecting wires and replaced it with the new one. I twas so fast and easy. I thought I was going to need a new Oven!!!!!Thank goodness for your website!!!!!

First I removed the two screws that hold the element in place againts the oven wall. I then pulled the element out about 3 inches and disconnected the two wires. These wires were screwed into the element so it was important to order the correct screw-in type replacement element. I pushed the wires back into place and screwed in the plate that holds the element against the oven wall. It was very quick and easy.

I simply removed the 2 mounting screws, pulled the element out a few inches, disconnected the 2 screws holding the wires to the terminals and reversed the order for assembly.

REMEMBER to turn off the breaker at the panel because the wires are still hot even though the oven control itself is off (trust me!!!).

Excellent service and fast delivery from partselect.com........ I'd gladly deal with them again.

The hardest part of this entire repair was locating the right socket and explaining why/how I burned my fingers (yes I had to touch the element to prove to myself it was that easy to fix and worked). 4 screws, 1 replacement part 5 minutes no cussing. This was the easiest repair I have ever done.

I was lucky to look at other repair stories because I forgot to turn off the power!!! Nothing happen to me, but it was as simple as everybody else said. Unscrew the two screws, pull out element, unscrew another two screws and put back together in reverse order. Viola, the oven was back in working order just in time for a major event the next day. Thanks everybody for their tips and partselect for fast shipping.

I turned off the breaker, removed two screws that held the element in place, pulled it out about four inches, disconnected the screws securing the wires to the element. Removed the old element, placed the new one in the oven and reversed the procedure.

First turned off the circuit that controlled the power to the Stove/Oven.
Then I removed the screws that hold the element in place.
I pulled the element out a few inches and disconnected the wires.
I attached the wires for the new element.
I replaced the screws.
I turned on the circuit.

And to reward myself baked a Coffee Cake. Yum!