20RJ736H Hotpoint Range - Instructions

Removed 4 screws and removed the old element and replaced in the reverse order.

less than 15 minutes R2 the part, ops ck'd good. 4ea 1/4" screw/nuts, they didn't fight me...

Removed old, burned out element, and replaced with a new element. The worst part of the entire job was getting the oven door assembled back on to the oven.

removed old element rewired new element,turned back on power

I diagnosed the problem as a burned out element. Received the part the next day (very quick service) My husband replaced the old element with the new. My broiler still doesn't work. I don't blame the company, my diagnoses was wrong. I have called the appliance repairman and it will probably be an expensive fix.

I thought I had founf "oven rack" on the parts diagram and I ordered it. It turned ut to be the wrong rack. I looked at the website again and found that farther along the set of diagrams there was a different style of rack with the little extra keeper-wire-prong features I needed. Two different diagrams and two different racks for what appeared to be one model. Service was excellent, no problem other than cinfusion w/ith diagrams and model numbers.

From inside the oven after turning off the breaker I removed all of the mounting screws with a nutdriver, I removed the wire screws after taping all of the wires together with a small piece of tape to prevent them from falling back into the opening. I installed the wires with the original screws as the provided screws would not fit the holes, tightened them, removed the tape and placed the element back into the opening. I then tightened the hanging brackets, after getting them to align and then tightened the rear mounting bracket. It did help to adjust the baking rack down and leave the baking rack in place to have a place to rest my arms. The install then became a piece of cake!

Removed old element, checked continuity and element was bad, Fit new element and everything was good. No problem except my arms were not long enough!! Repairs took about 15 minutes.

TURN OFF POWER , remove oven door & oven wire racks, remove two retaining screws in back of coil and pull the burnt coil foward enough to remove the screws that hold the wires to the coil. You may have to drop one side of the front support bracket to move coil forward.Fasten the new coil to the broiler wires with the new screws provided. Push the new coil back into place being careful not to pinch the wires in the opening. Refasten coil to the oven back with existing screws that you removed. Refasten front support.Put racks back in and put door back on.Easy fix! Easy to order, easy to install and came within days from order date. Very pleased with whole thing.

First turn off breakers. Undo all screws and remove burner. Easy to see how to replace old part with new. Self explanatory if you follow what you have taken apart.

The broil element was easy to replace. Start by either unplugging the unit from the wall or turning the circuit breaker off. I started by removing the two screws that hold it in the back. There was a support bar attached to the top with two screws also. After removing all screws, gently pull the element forward exposing the two wires. Make note of which wire goes to which terminal. I also clipped a clothes pin to each wire to prevent them from falling back through the hole. Disconnect the two wires and reconnect to the new element. Reattach all screws and you're done.

First I turned the power to the stove off at the breaker box. Next I removed the two screws holding the old element in place against the back wall of the oven. I gently pulled the element forward. I wound a couple lengths of spare colored wire around the two electrical wires before disconnecting the retainer screws at their connection points. This insured that the electric wires would not fall back inside and behind the firewall. I then disconnected the screws holding the electrical wires to the broiler element. I removed the element from the oven and discarded it. I then connected the screws through wires and the connecting points of the new element. I removed the spare wires hold the electrical wires. I positioned the broiler element in place and screwed in the retainer screws securing it in place. I turned the breaker switch to the "on" position and tested the new broiler element. It tested fine. Job done in 15 to 20 minutes. An able bodied person could do it in less than 10 I'm sure.

Just re-connected the electrical. Was the exact/correct replacement part. Repair successful. Thanks.

Some times it's not the element at all, as in this case. After rmoving the element I found the wires broke. Fortunatly I had some high temp wire left over from a earlier oven repair. I used butt splices and heat shrink tubing to repair the wires. Then I crimped on a couple of eyelets and fastened things dow.n I received a big kiss form the wife for getting the broiler fixed so fast. Maybe a little extra work, but the rewards were worth it.

Unscrew 4 easy nuts and 1 most difficult nut, gently pull both long and short wires, at this point assure the wife that you did turn off the power.You may wish to attach a cord to short wire as it wants to vanish into the rear bowels of the oven On instruction of the wife clean the oven. Reverse dismantling procedure. Switch oven on. Bask in wives praise.