RB5251R3 Hotpoint Range - Instructions

Unplug coil, remove pan - place new pan, plug in new element and bingo. Took approximately 30 seconds!

I took out the old broiler support bar, but it was being held by one screw. I did install the new bar with one screw, but I need to obtain a second screw. I still have not located a second screw, but it is inplace.

Partselect made this job a breeze. Due to the user friendly process to order and receive the part. I repaired the stove after turning off the breaker in the main box. There were two screws that held the baking unit in place, removed them and then replaced with new unit.

turn off electricity to stove and simply remove the screws from the heating element and put new element back in place .put screws in and turn power back on and test.

Surface element easily unplugged and removed, drip pans lifted out, New drip pans inserted, New 8" surface element and present 6" surface elements Inserted and plugged in.

First removed oven door, according to Reader's Digest repair manual, then removed two screws holding element. Pulled element out several inches, then removed one side of bracket holding up front of element so that bad element could be pulled further out. Then disconnected two red wires from one side and two light blue wires from other side. Removed old Element. Attached two light blue wires to one side and two red wires to other pole, inserted element back into rear wall and attached with two screws, Re-attached bracket holding up front of element. Re-installed door. Tested and it worked fine.

I am a 62 y/o single female and was able to make this exchange of parts with ease. The toughest was getting the old terminal's wire clips free from years of gunk! I was pleased with the ease of installation and that it really worked afterwards. By the way, thank you Parts Select for getting this part to me very quickly. If a novice can diagnose, find the correct part and install it with success then anyone could do the same.

Removed existing surface element and replaced with new element.

P.S.

Part Select service was excellent.

OK, I put the drip pan under the burner. Without a single problem.

Got new part! Unplug range!!!
Remove oven door by opening and lifting up at the same time, set aside.
Remove two screws with a nutdriver or screwdriver.
Pull on element far enough to unhook wires and throw away old element and install the wires on the new element and reinstall!!

Because of the superb pics and descriptions on the Part Select site, I was able (with NO range model number) to order the correct range element for beloved son's stove. He plugged it in in 3 seconds, works great !

I looked on Youtube for a how to video. It was accurate but the screws in my oven were NOT phillips head screws, they turned out to be sheet metal screws. I used pliers at first which was a PAIN but then I borrowed a socket wrench from the neighbor that was MUCH better!! I had wanted to do it myself to prove to my husband and son that I could but I ended up needing their help because the screws were so tight.... But we did the repair ourselves!!!

Broiler element arrived at my door 3 days after ordering which was nice. Apparently the billing dept. is out of the USA so don't be surprised, like I was, to find a suspicious looking charge for a currency exchange fee (mine was 42 cents). I had to drill two new screw holes in the base of the new element in order for it to fit my oven. I also had to use heavy wire snips to cut off about an inch of the top of the new element base. The female electrical connections also had to be spread out with needle nose pliers since the new element connections were slightly thicker. With all of the issues I had I was frustrated and it took about two hours. On the other hand, the part works perfectly and was priced right. Hopefully it will fit perfectly out of the box for your oven.

I removed the unit easily with anut driver, however the unit also supported the thermo-link. I had to use the hack saw to relieve a small opening for the thermo-link to pass through. No real problem. Then a few holes to be drilled to attach the 'link' to the base of the broiler unit.

BUT-I went into the website listed on the box. GEAppliances.com Guess what? Their price was twice yours!!

Took Switch panel off range. Disconnected Infinite switch. Reinstalled infinite switch.. Replaced panel. Repair was very simple and self explainatory.
Knott County Housing Authority Maintenance Personnel