RB636303 Hotpoint Range - Instructions

Removed old terminal block by removing one mounting screw. Removed two wires from block. Installed new terminal block by reversing procedure.

Tried contacting GE and no luck, they did not have vintage parts. After searching and locating Partselect, I was able to see a pic of the actual replacement part. I wasn't sure about purchasing online (1st timer) but decided to go for it!

I was able to track the package, although FedEX was setup to deliver to my resdient, I had the package addressed to my office but we worked that out also and walla.

I was very please and now I can bake my famous Pot Roast again. The oven was not working for 8 mos.

Good Eaten!

SJ-Long Beach CA

I removed the burner, then the chrome dish. The nuts for the wires were rusted to the terminals, so I had to break the module apart and grind the nuts off.After that the new module went fine.

Your "virtual repairman" was fantastic. I would have purchased the wrong part without trhe diagnostic service. It said that 53% of the time the infinite switch was the problem. In my case it was 100%. Why I put up with this problem for 6 years I will never know.

Repair job was easy but longer than the 15 minutes that it said it would take.

First of all I did this repair because the wire to the burner shorted out. I did the wire portion first - only then did I know I needed the switch kit. (The burner was operating while my old swithch was OFF). The first (wire replacement) repair took about 10 minutes - I followed the guidance on this web-site. The second repair (The switch) took about 20 minutes. The switch ws not the same as the original. Just be careful to mark each wire as you remove them from the old switch's posts. The posts on the switch are marked and you need to place them on the like-marked corresponding posts on the new switch. All is well, my burner is operational.

1. The infinite switch had several knobs which would fit the switch shaft. Read the directions included with the switch in order to have the shaft fit the proper knob. You can break the shaft with two pairs of pliers. 2. Move the stove away from the wall and unplug it. 3. Remove the 1/4 screws from the back side of the stove and remove the back panel, exposing the switch. 4. Remove the wires one at a time and put them on the new switch. The terminals are L1, L2, P, H1 & H2. The Pilot (p) has a smaller terminal so you don't get it mixed up. Generally L1 is black, L1 is red, P is yellow, H1 and H2 can be blue, brown, yellow, orange or one of these colors striped on a white wire. 5. Remove the old switch from the stove and be sure to save the two mounting screws. 6. Position the new switch so that the side of the switch marked "top" is on top. 7. Install the screws on the new switch and put the knob on it. 8. Carefully test the burner. 9. Unplug the stove and put the back cover on.

The repair was a bit difficult because the screws connecting the wires to the element were small threaded bolts and no slot for a screw driver. They were very difficult to break loose - that's when we used the Liquid Wrench and waited. Other than that, the repair went smoothly. It is better to remove the oven door, if you can, otherwise the rear of the oven is not as accessible. It is also a good time to change the light bulb.

Simply removed the old one and replaced it with the new one. Part Select was the only company that was able to identify the part without the Model Number. The Model number was
worn off and unable to read. After going through several
on-line parts dealers, Part Select was the only company that could identify the part I needed. The repair was simple and
short. My old stand by oven is in operation again.
Thanks, Laura

I unplugged the stove, unscrewed two nuts, pulled the two wires forwrd and disconnected them. Attached the wires to the new burner and it works fine!

It was quite simple after the part arrived. I actually had forgotten what the connection was because one wire was yellow and one was red. After calling the number that I had to no avail. I went to the computer to ask how to install the part. Installed in little to no time. Feel like a Jill of all trades. Bring on the next problem.

Element was in two pieces so it was obviously dead. I disconnected the stove from the power, I undid the two screws at the back of the oven and gently pulled the element out. There was enough slack to reach and pull the connectors apart. Done. I ordered the part from "PartSelect" and it arrived the next day. Unfortunately I ordered the element with "Screw" convectors as opposed to "push on" connectors. I bought a couple of connectors and cut off the original connectors from the wires in the oven and replaced them making absolutely sure they were well and truly tight. Two screws cam with the element from "PartsSelect (Thankfully). Connected the wires and screwed it back into place. Stood clear, plugged it in and turned it on to max. Worked just fine, Thanks

simply lifted the heat coil and slid the rings off and lifted the drip pans off. Vacumed the bottom underneath the old pans. Cleaned the grease off around the stove where the rings sat. Let it dry and added the new rings and pans. Looks like it did 30 years ago.......let them try making a stove last that long today !! Make sure the power is OFF at the electrical box.

The only hard part of the job is removing the old, corroded terminal block. Be careful not to break the electrical wire. Other than that, just sand the contacts and reassemble. This is the second one I have replace on my 4 burner stove. 2 more to go.

I located and removed 2 sets of hex-head screws under the front lip of the cooktop, then lifted the entire cooktop to access the burner controls. Removed the wires and taped them, and took out the old control after removing 2 phillips head screws. Installed replacement part easily. Only tricky part is that the various shaft adapters don't quite work with my knob. I'll fix it completely with a bit of epoxy and the adapters they sent.

It was so easy, we got on the General Electric web site and entered the old model number, found our match and ordered the part. It came 3 days later and it was so easy to remove the old one and install the new one, only two screws to remove. Saved a lot of money by doing it ourselves! Thank goodness for websites like this!!