RB636303 Hotpoint Range - Instructions

My husband helped me pull the range out from the wall to unplug it, I removed the screws on the hinged bracket, pulled the wiring out a couple of inches and removed the screws attaching the element to the wiring. Then I reversed the process. Easy as pie. The most time consuming part was unplugging the range, but as it is 220v (can kill you) I consider it a nesessary step. The best part was the price and availability. I ordered the part on Sunday p.m. and got it on Tuesday p.m. at half the price quoted by a national chain.

First I removed the two screws that hold the element in place againts the oven wall. I then pulled the element out about 3 inches and disconnected the two wires. These wires were screwed into the element so it was important to order the correct screw-in type replacement element. I pushed the wires back into place and screwed in the plate that holds the element against the oven wall. It was very quick and easy.

I simply removed the 2 mounting screws, pulled the element out a few inches, disconnected the 2 screws holding the wires to the terminals and reversed the order for assembly.

REMEMBER to turn off the breaker at the panel because the wires are still hot even though the oven control itself is off (trust me!!!).

Excellent service and fast delivery from partselect.com........ I'd gladly deal with them again.

The hardest part of this entire repair was locating the right socket and explaining why/how I burned my fingers (yes I had to touch the element to prove to myself it was that easy to fix and worked). 4 screws, 1 replacement part 5 minutes no cussing. This was the easiest repair I have ever done.

I removed the screws holding the element in place. I pulled the element out from the back of the oven about 3" and then disconnected the two wires. I then reattached the two wires to the new element and pushed the element back flush with the rear of the oven. I then rescrewed the two screws that hold the element in place. That was all there was to it.. Very easy. I am 54 years old and have never done this before.. So if I can do it so can you....

The terminal blocks become brittle and carbonized with age resulting in very poor contact with the electric burners. The burners lose capacity to heat fully and eventually stop working.

Unplug the stove first! There is a risk of dangerous electrical shock if the power is not disconnected.

Repair involves removing the burner and the drip cup to expose the terminal block. Remove one screw on top to detach the block from the stove top. Remove the insulating cover and the clip that holds it in place on the back of the block. Detatch the two wires. At this point the age and brittleness of the blocks became apparent as they crumbled in my hand while removing the terminal screws. One screw had several layers of carbonization covering it and required needle nose pliers to get a firm grip in order to loosen it.

Inspect the wires to make sure there are no holes or cracks in the insulation.

Attach the wires to the new terminal block using the new screws provided. The new kit also included quick lock screw fastener clips to place over the holes in the stove top. It's a good idea to use these for more secure mounting and better grounding. Place the new terminal block under the stove top and mount it with the new screw provided. I had to unbend the mounting clip slightly to get it to fit, but it was easy enough to do with bare fingers.

Replace the drip pan and the burner. Plug the stove back in.

A pot of water now boils in under a minute compared to the 5 to 10 minutes it used to take.

I used a philip screw driver to remove two screws which enable me to pull the wires out about three inches from the back of the oven and replaced it with the new one after disconnecting the wires from the grill. The hardest thing was the limited space.

Turned off breaker,first . Then removed 2 nutscrews and pulled unit out , 4 inches ,removed 2 nutscrews joining the 2 wires and the 2 terminals of the bottom element. Removed bottom unit and replaced with new unit . reversing the process. Turned breaker on and tested the oven. Works fine. Took less than 15 minutes.

turn power off at circuit breaker box, remove old coil from oven, attach the new coil and attach to wall of the oven. Very easy to repair.

I was worried at being able to locate the part as the oven is over 35 years old. I put in the old part number on your site and it gave me the correct replacement. On my model you unscrew the two screws securing the element to the back of the oven. Then pull out the old element carefully because the wires are screwed onto the element. I pulled it out 4 or 5 inches and unscrewed the wires and connected the wires to the new element. I then threaded the wires back into the hole at the back of the oven and screwed the element back in place. Works perfect.

First, turn off the power. Remove the two retaining screws, pull out the broken element far enough to unscrew the connectors, remove the element, reconnect the new element, screw it back in, turn the power back on. Yes, it is that easy! Took me all of five minutes. Took longer to find my tools!

The complete repair was quick, easy, and painless. Not only did my item show up sooner than I thought the whole replacement took only 15 minutes, tops, to complete. I even had my 18 months old daughter helping too.

First and foremost I turned off the power to the oven by tripping the circuit breaker in the basement. Then verifying that the oven or stove top did not work to insure that the correct circuit breaker was tripped.

Then I removed the two mounting bolts on the support plate, that holds the element in place, from the rear wall of the oven. Then slide out the element just far enough to gain access to the wires that are attached to the element, about 3-6 inches. Carefully removed the two wires from the element with a screwdriver, noticing how flexible the ends of the element were. Removed the old element out of the oven. Placed the new element into the oven and then reattached the two wires to the new element terminals, being careful not to bend the ends of the element too much, very flexible!! Slide the element back into place and then reattached the mounting bolts. Turned all power back on to the stove and then turned the oven on and presto!, my oven is fully functional again.

Customer service is great. Fast shipping. Great communication. I have them bookmarked from a previous order. Same good service as the first time. Thank you.

Removed 2 screws (with 1/4" nut driver) on bracket holding heat element at back of oven. Pull element forward to expose the 2 wires connected to element, remove screws on wire corrections with flat head screw driver. Remove element from oven......Reverse the steps to install new heat element.....very easy job....except I cleaned the oven while I had the element out of the oven.

lift eye slide in bowl and trim ring, put the eye back down,