RK747*T3 Hotpoint Range - Instructions

Easy! Removed the screws, took out the damaged element, reversed the process with the the new element. I called in my order on Monday and Wednesday evening the oven was repaired! It doesn't get any better than that. Thanks for the great service.

First I Shut off the breaker from the fuse box
Tried to turn oven on to make sure I tripped the correct breaker
Removed element from back wall of oven by removing 2 screws using a socket set
Gently pull out element a few inches and then unscrew 2 wires from the bake element using a phillips screwdriver
Replace old element with the new one
Screw wires to element
Attach new element to back wall of oven making sure the rectagular hole is totally covered and the element is flush against the back wall
Replace screws attaching baking element to back of oven wall
Turn on breakers and test the oven

replaced with a new part . Thanks for all your assistance in getting the correct part

remove two screws from back of oven holding element to back of oven. Pull out gently, remove two screws holding wire connections(power wires) throw away old element. Place new element into oven. Reconnect element to power wires using screws. Push element back into back of oven. Replace screws holding element in place. Turn oven on to check for proper connections.

You website was quite easy to use and we found the part really quickly. After we ordered it, it was delivered within 5 days and was easy to install. I was a happy camper to have my oven back which I use a lot. Thanks for the quick delivery and information. Candi

Removed the two screws that held the element in place. This required the use of a socket wrench. Removed the screws that were attached to the lead wires. The screws were of the sheet metal type.
Once the new element was in place I did have some difficulty attaching the screws to the lead wires. The reason for this was because the screws that came with the new element were threaded and I had a hard time getting the screws started because of the small size and the limited amount of slack from the lead wires. A magnetic screw driver would have made the job much easier.

It was quite easy. We first turned the power off at the main power switch. Once the power was off, we removed the two screws that fastened the metal plate in the back. We pulled the old bake element out and removed the two screws that fastened the element to two wires. To fasten the new bake element we simply reversed the procedure.

Turned off breaker, unscrewed holding plate, unscrewed element from electric connection wires, replaced element and screwed all back together, turn on breaker, oven working fine now. E-Z!

Easy repair. The toughest part was disconnecting the wiring from the old element. Once that was disconnected it went very well.

After checking the website, I wasn't sure the part I needed was available. Called the Customer Service number and the lady was very helpful.
My part was delivered in 2 days regular UPS.

The most time took finding which breaker shut off the power to the oven. Removed two screws on the inside of the oven at the back wall. Pulled out the wiring and removed two more screws that attached the power to the element. Replaced the old element with the new one. Reversed the process. Done in 12 minutes! Very easy.

Removed the two screws holding the mount and then reattached the two wires to the element.

First I shut off power to the oven. Then, using a nut driver, I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and unscrewed the two screws that make the electrical connection. Removed the old element and put in the new one.

Turned on power and ran the oven for a while to verify that it worked and to burn off any oils on the element.

Removed the 2 screws that held element in place. Pulled the element out about 2 inches to disconect the wires. I then reattached the new element and replaced the screws holding the element in place.

took the element screws off, a little bit dificult to fine the small wrench socket to disengage. I had to have my husband do it because I have too short arms.
I can't believe how much money we saved., the part was there within two days and installed, for a total of 52.00 including next day Fed ex.
Feel good about the whole expierence.

Shut the power off to the stove. Removed the screws and pulled the old part out. Replaced with new part from Parts Select.

Your service is excellent. I received the part within two days of it being mailed. The emails received from you were very helpful and also confirmed the transaction.
Thank you very much.