RS776G101 Hotpoint Range - Instructions

First removed screws then removed burned out element.Replaced with new element and replaced screws and cooked pizza.

popped the new one on!

I followed the easy instructions and everything went well. I had the new switch installed in about 30 minutes. My wires were different colors than on the instructions but it was still easy to figure out where the wires went on the new switch. Just do not be in a hurry and make sure you measure before you break off the extension bar. My knob fit on the new switch without any of the parts that came with the switch.

Turn off the breaker. Unscrew the element. Remove and replace with new element. Screw it back into place. Turn on the breaker.

That simple, that easy.

First I removed the two screws that hold the element in place. I then pulled the element out about 2 inches and disconnected the two wires.

I reconnected the two wires to the new element and screwed the new element to the wall of the oven where the element was held in place.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I reattached them to the new element screwed it back in place and I was done. Could not have been easier! Getting the right replacement part the next day after placing the order was a pleasant surprise. This is the second time I used your company and I am very impressed with your service. I recommend you to everyone I can. Great Job!

I ordered the bake element on Monday and received it on Wednesday. Great delivery.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...
Then I installed the new element using the steps above in reverse. Very clean and simple. One tip though...open your oven door slightly to the detent and pull straight up. The door slips off easily and allows easy access to the bake element screws.

Removed old terminal block by removing one mounting screw. Removed two wires from block. Installed new terminal block by reversing procedure.

Tried contacting GE and no luck, they did not have vintage parts. After searching and locating Partselect, I was able to see a pic of the actual replacement part. I wasn't sure about purchasing online (1st timer) but decided to go for it!

I was able to track the package, although FedEX was setup to deliver to my resdient, I had the package addressed to my office but we worked that out also and walla.

I was very please and now I can bake my famous Pot Roast again. The oven was not working for 8 mos.

Good Eaten!

SJ-Long Beach CA

I removed the burner, then the chrome dish. The nuts for the wires were rusted to the terminals, so I had to break the module apart and grind the nuts off.After that the new module went fine.

First of all I did this repair because the wire to the burner shorted out. I did the wire portion first - only then did I know I needed the switch kit. (The burner was operating while my old swithch was OFF). The first (wire replacement) repair took about 10 minutes - I followed the guidance on this web-site. The second repair (The switch) took about 20 minutes. The switch ws not the same as the original. Just be careful to mark each wire as you remove them from the old switch's posts. The posts on the switch are marked and you need to place them on the like-marked corresponding posts on the new switch. All is well, my burner is operational.

Your "virtual repairman" was fantastic. I would have purchased the wrong part without trhe diagnostic service. It said that 53% of the time the infinite switch was the problem. In my case it was 100%. Why I put up with this problem for 6 years I will never know.

Repair job was easy but longer than the 15 minutes that it said it would take.

I located and removed 2 sets of hex-head screws under the front lip of the cooktop, then lifted the entire cooktop to access the burner controls. Removed the wires and taped them, and took out the old control after removing 2 phillips head screws. Installed replacement part easily. Only tricky part is that the various shaft adapters don't quite work with my knob. I'll fix it completely with a bit of epoxy and the adapters they sent.

First -- and thank goodness I read some of these stories first or I would have forgotten -- I turned off the circuit breaker to the stove.

I removed the two nut screws holding the element itself to the back of the over. Then I removed two more nut screws holding the element to the electrical wires. (This took some WD-40. The stove is about 25 years old.)

That was about it. Everything lined up perfectly, and there was nothing more to do except reconnect the new element and throw the breaker back on. It works!

I removed both screws to remove lower element, and measured it prior to ordering the replacement.
Then in a few days it arrived, and I installed it. The new element had small bolts rather than screws the original used to attach both wires. A flashlight was necessary in locating an keeping an eye on the wire ends, to keep them from being pulled inside the back cover, as the bolts were attached.