RA513401 Hotpoint Range - Instructions

I logged into GE's website, put in my stovetop's requirements for size and type of trim rings, and was taken to partselect's site where I found what I needed. I ordered it and it came in less than a week!

just replaced the old for the new

The replacement was easy: turned off breaker to range; unscrewed element from range top;opened ceramic terminal box; unscrewed element from range wires. Then I simply reversed the procedure, using the new parts. Easy to do and it only took about 10 minutes.

Took coil mounting assembly off first, then removed or took apart one piece at a time until heater coil was removed. Then installed (with furnished screws)the new coil, following entire process in reverse. 10-15 minutes time.

A simple repair using your quality matched Part turned into a CONDOMINIUM CIRCUS (no fault due to the Part or PartSelect.Com.)

It was the 1st time in over 30 yrs. that we had to throw a Circuit Breaker Switch located outside in the communal large Metal Box between Condos. Not only did it NOT cut the power off our old GE Range - it turned off one neighbor's T.V. & another neighbor's Washer/Dryer Set.

As more Breakers were tried - MORE ANGRY NEIGHBORS ARRIVED ON THE PATIO. To complicate this - the next-door Condo just underwent extensive (read 3 Months) Renovation including REPLACING ALL WIRING..... and you might imagine the rest. No Breaker Switch numbers matched the Condo number written beside them in felt tip pen... it was complete chaos!
THANKS to PartSelect.Com our old G.E. is working again.

Yours truly,

William Rush,

it was hard to figure out the instructions from A switch to B switch to my switch. The first switch was no good the second one was good. prayer book didn't hurt.thank

Replaced the old with the new following directions (mostly).

Good directions

The original controls were different for the small burners and the large burners. The replacement part fits all. Before removing wires, pay attention to writing on new and old control and replace 1 at a time. The hardest part was being sure to cut the knob stem to the correct length. Control works well.

I flipped breaker off for electic and confirmed that power to the stove was off. I removed the 2 screws holding the control unit in place. Carefully removed all knobs and buttons and pryed the cover for the control unit off. I then removed old part, removed the wired and clipped wires to the new unit. Put cover back on - has some difficulty getting the panel back in place to line up the screws. But after a couple of attempts, was able to line up unit and put screws in place to secure. Replaced all knobs. Turn breaker back on and cooked lunch. Very easy job. Most difficult part was getting panel back in position. I would watch alignment more carefully before I removed in next time. Easy home repair for Women...not sure about my man?

(Turn off the Power) Pull stove out, remove the 2 screws that holds switch in place, remove one wire at a time and install on new switch. Slip switch in replace 2 screws. Snap off about 3/4 of the shaft cut down plastic insert for knob, install knob turn on power and it works.

Put bowl in and then slid rings around. Just like cleaning procedure. Easy. Thanks for your service.

Simply removed old and inserted new. No tools necessary.

slid the range away from wall. disconnect power. removed back,compared switches and marked wires.installed new switch and wires.the adapter for the control knob was a problem it left the knob out futher than original i had to modify the plastic adapter and got it close enought! the most time spent was cleaning up the floor before putting the range back.

Turned off the breaker to the range. Turned on range to ensure no electricity was currently flowing to the range. Turned the range off and unscrewed the tilt lock hinge. Pulled the burner out to expose the wires. Popped the snap locks off the cover box and unscrewed the wires connected to the posts. Followed recommend directions to expose approx. 1/2" of new wire (this is what I used the knife for since I did not have a wire stripper available). Slightly cut thumb in the process (no blood, though). Removed old burner. Put new burner in place, re-attached wires to the posts and screwed in to place. Placed cover box back in place and secured using new snap locks. Attached tilt lock hinge using new screw that was provided. Turned breaker back on and turned on range. new burner worked great. Took about 20 minutes total. Wife was extremely impressed, mostly that I didn't electrocute myself. She now wants me to replace other three burners. No good deed goes unpunished.