207RHV786J Hotpoint Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Glenn from Plano, TX
- Parts Used:
- WB44X173
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers
broil element failure
Unscrew 4 easy nuts and 1 most difficult nut, gently pull both long and short wires, at this point assure the wife that you did turn off the power.You may wish to attach a cord to short wire as it wants to vanish into the rear bowels of the oven On instruction of the wife clean the oven. Reverse dismantling procedure. Switch oven on. Bask in wives praise.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rod from Huron, OH
- Parts Used:
- WB21X36771
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
rht. front element would not heat properly
I read parts select instructions and i was done in less than 30 minutes. Since 1988, this is the 1st. part that I had to replace. I now have parts select on my favorites list.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pauline from Helena, MT
- Parts Used:
- WB44X195
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Old element was burned out. Haaven't figurerd out how this happened.
Just unpluged the old one and detached the wires. put the new one in and used a socket wrench to rewire it. . Very easy and was shipped in perfect condition and easy to replace. Very pleased.It fit perfect and oven works just fine. Thank you so much for the service which was very speedy. It was packed to perfection.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Mendota, IL
- Parts Used:
- WB44X173
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
broiler element burnt thru
TURN OFF POWER , remove oven door & oven wire racks, remove two retaining screws in back of coil and pull the burnt coil foward enough to remove the screws that hold the wires to the coil. You may have to drop one side of the front support bracket to move coil forward.Fasten the new coil to the broiler wires with the new screws provided. Push the new coil back into place being careful not to pinch the wires in the opening. Refasten coil to the oven back with existing screws that you removed. Refasten front support.Put racks back in and put door back on.Easy fix! Easy to order, easy to install and came within days from order date. Very pleased with whole thing.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Myer from Cleveland, GA
- Parts Used:
- WB44X173
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Broil Element burned out
Removed old element, checked continuity and element was bad, Fit new element and everything was good. No problem except my arms were not long enough!! Repairs took about 15 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ken from Temecula, CA
- Parts Used:
- WB44X173
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Oven not getting hot to preset temp
First turn off breakers. Undo all screws and remove burner. Easy to see how to replace old part with new. Self explanatory if you follow what you have taken apart.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Avril from Wasilla, AK
- Parts Used:
- WB32X10013, WB32X10012, WB31X5014, WB31X5013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Old very stained drip pan and rings
Simply removed old and inserted new. No tools necessary.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Floyd from Warren, OR
- Parts Used:
- WB21X36771
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Plastic Insert for knob to long, had to use my bench grinder to cut it down
(Turn off the Power) Pull stove out, remove the 2 screws that holds switch in place, remove one wire at a time and install on new switch. Slip switch in replace 2 screws. Snap off about 3/4 of the shaft cut down plastic insert for knob, install knob turn on power and it works.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leonard from Winter, WI
- Parts Used:
- WB21X36771
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
element heat wouldn vary
slid the range away from wall. disconnect power. removed back,compared switches and marked wires.installed new switch and wires.the adapter for the control knob was a problem it left the knob out futher than original i had to modify the plastic adapter and got it close enought! the most time spent was cleaning up the floor before putting the range back.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Norma from SAN JOSE, CA
- Parts Used:
- WB44X195
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
The Upper oven the lower element went out.
Unscrewed the prongs to the old element. When the new element showed up I put the new element back in again. Had no problem with the replacement and my oven works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from San Antonio, TX
- Parts Used:
- WB32X10013, WB32X10012
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
Old drip pans rusted out.
Range is 45 yrs old. New drip pans are different shape. This is only place which had them and VERY GOOD price. Delivery was quick, too!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chuck from Ellettsville, IN
- Parts Used:
- WB44X173
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Broiler Element burned out
From inside the oven after turning off the breaker I removed all of the mounting screws with a nutdriver, I removed the wire screws after taping all of the wires together with a small piece of tape to prevent them from falling back into the opening. I installed the wires with the original screws as the provided screws would not fit the holes, tightened them, removed the tape and placed the element back into the opening. I then tightened the hanging brackets, after getting them to align and then tightened the rear mounting bracket. It did help to adjust the baking rack down and leave the baking rack in place to have a place to rest my arms. The install then became a piece of cake!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Fort Wayne, IN
- Parts Used:
- WB44X195
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
The oven coil burnt out visibly sparking at the failure point on the coil
This model has a top oven and a bottom. The repair was to the top oven. I shut off the electricity to the oven at the circuit breaker box.I removed the grates and unscrewed the two screws holding the burner in place. I gently pulled the burner free along with its two attached wires. I removed the two screws that retained the connections to the burner. I installed the new burner in the reverse order. Turn on the circuit. Good to go.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ROBERT from SEATTLE, WA
- Parts Used:
- WB44X195
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Upper Oven Lower Element Burned Out
Took off the oven liners, took out 2 retaining screws, pulled out element, removed wires, reversed procedure, easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Bremond, TX
- Parts Used:
- WB30X342
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
heating element burned out.
Replaced 30 year old stovetop cooking element with no problems. Stovetop works great now.
Was this instruction helpful to you?
Thank you for voting!