RC548*W1 Hotpoint Range - Instructions

unplugged oven. removed oven racks.Disconnected old unit. Installed new unit. Very very simple

With great ease. Only thing I would have appreciated was knowing the size ofvthevrequired socket wrench. Otherwise it was easy and fun as the instructions were crystal clear.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Then I replaced it with the new element that took only two days to arrive and that was without paying extra express shipping fees. It couldn't have been easier. I didn't even wait for my husband to come home and install it. I had an oven-baked meal ready when he got home. I was very satisfied.

First of all I did this repair because the wire to the burner shorted out. I did the wire portion first - only then did I know I needed the switch kit. (The burner was operating while my old swithch was OFF). The first (wire replacement) repair took about 10 minutes - I followed the guidance on this web-site. The second repair (The switch) took about 20 minutes. The switch ws not the same as the original. Just be careful to mark each wire as you remove them from the old switch's posts. The posts on the switch are marked and you need to place them on the like-marked corresponding posts on the new switch. All is well, my burner is operational.

Your "virtual repairman" was fantastic. I would have purchased the wrong part without trhe diagnostic service. It said that 53% of the time the infinite switch was the problem. In my case it was 100%. Why I put up with this problem for 6 years I will never know.

Repair job was easy but longer than the 15 minutes that it said it would take.

First I removed the 2 screws holding the element in place then pulled the element out a few inches.
I removed the 2 screws that connected the wires to the element and removed old element from oven. The new element was placed in the oven and connected by reversing the steps just described. New element works perfectly!

Two screws to remove the element and two screws for the wire connectors and it was done.

Turned off circuit. Unscrewed old element. Connected new element and screwed it in. Worked like a charm. It shipped very quickly. Could not be more satisfied; total repair: $30 and prevented me from buying a new oven; satisfaction: priceless.

Open oven door about 3 inches - then holding on the door on either side - pull up and door slides off - put it aside - this is to make it easy for you to work inside oven compartment - at rear of oven where the element goes into the back wall - there are two nuts to remove - I did not have a nut drive so used a pliers (GE could have put slots in the nuts so one would just need a screwdriver) - pull element forward - there are wires attached to the 2 ends of the element - remove with screw driver - element is off - get new part from PartSelect -(and must say pleased with their service) - and reverse above procedure.

First I turned the power off to the oven at the breaker box. Then I removed the nuts holding the element to the rear wall of the oven and pulled it out a couple of inches. I saw that only 2 nuts held the element to the wires. I found the part on your site very easily and placed my order. The part was at my door 2 days later! I removed the old element, replaced the new element and turned the breakers back on. Repair complete!

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...removed the baking element and put the new element back in the same way I took the old one out. It was great directions that was posted and easy to do. Best of all I saved the price of a service call. Thank you

First I turned off the power to the stove,removed oven racks,removed the two screws that held the element in place,pulled unit out a couple inches ,removed the two screws that held the wires in place ,removed element.
Placed new unit where old one went and placed wires in proper order and put together and placed back . turned power back on and WALAA......nothing......apparently that wasnt the problem....Husband baught me a new stove,after 35 years why not.

Unplugged oven, removed 2 screws that hold the element in place. Pulled element to expose wires. Disconnected wires & removed old element. Reversed removal for installation, plugged in and worked great.

1) turned off breaker to oven
2) removed oven racks
3) removed screws holding old element
4) pulled out element far enough to remove 2 wires attached to old element
5) noted colors, left white, right black
6) attached new element to wires
7) attached new element to oven
8) put back oven racks
9) turn breaker back on
10) test oven
done
EASY!!

First, I turned off the circuit breaker. Then I removed the two screws on the hinged plate that attaches the element to the back wall of the oven. Then pulled out the two wires attached to the element by screws. I detached the old element and reversed the sequence to install the new element. Very simple operation for the average homeowner.