RK766*R3 Hotpoint Range - Instructions

First I removed the two screws that hold the element in place againts the oven wall. I then pulled the element out about 3 inches and disconnected the two wires. These wires were screwed into the element so it was important to order the correct screw-in type replacement element. I pushed the wires back into place and screwed in the plate that holds the element against the oven wall. It was very quick and easy.

My husband removed the old element by shutting down the power, then unscrewing the element. Then he screwed in the new element and turned oven on for 5 minutes to break it in.

Very simple and so cheap!

The hardest part of this entire repair was locating the right socket and explaining why/how I burned my fingers (yes I had to touch the element to prove to myself it was that easy to fix and worked). 4 screws, 1 replacement part 5 minutes no cussing. This was the easiest repair I have ever done.

remove 2 screws holding element to oven back wall/ unscrew wires from element/ new element install the reverse of removal

First turned off the circuit that controlled the power to the Stove/Oven.
Then I removed the screws that hold the element in place.
I pulled the element out a few inches and disconnected the wires.
I attached the wires for the new element.
I replaced the screws.
I turned on the circuit.

And to reward myself baked a Coffee Cake. Yum!

Removed 2 screws with nutdriver.Pulled element out to expose wiring and disconnect 2 wires also with nutdriver. Reverse process. Unit reaired.

removed the old heating element which had about two screws and two connecting wires and replaced it with the new one. I twas so fast and easy. I thought I was going to need a new Oven!!!!!Thank goodness for your website!!!!!

The repair was pretty easy. I unplugged the stove and took the 2 screws out that secured the element into the back of the stove. I then used a pair of needle nosed pliers to pull the wires off the element that wasn't working and then attached the wires to the new element. I then put the screws back in place securing the element to the stove and it was done. It took me about 5 mintues and the element worked immediately.

turn power off at circuit breaker box, remove old coil from oven, attach the new coil and attach to wall of the oven. Very easy to repair.

Used a nut driver to remove two hex screws holding element to the back of the oven and then the two hex screws connecting the element to the oven wires. I pulled the element out and reversed the process. I turned the oven on and made sure the element worked.

I was worried at being able to locate the part as the oven is over 35 years old. I put in the old part number on your site and it gave me the correct replacement. On my model you unscrew the two screws securing the element to the back of the oven. Then pull out the old element carefully because the wires are screwed onto the element. I pulled it out 4 or 5 inches and unscrewed the wires and connected the wires to the new element. I then threaded the wires back into the hole at the back of the oven and screwed the element back in place. Works perfect.

The complete repair was quick, easy, and painless. Not only did my item show up sooner than I thought the whole replacement took only 15 minutes, tops, to complete. I even had my 18 months old daughter helping too.

First and foremost I turned off the power to the oven by tripping the circuit breaker in the basement. Then verifying that the oven or stove top did not work to insure that the correct circuit breaker was tripped.

Then I removed the two mounting bolts on the support plate, that holds the element in place, from the rear wall of the oven. Then slide out the element just far enough to gain access to the wires that are attached to the element, about 3-6 inches. Carefully removed the two wires from the element with a screwdriver, noticing how flexible the ends of the element were. Removed the old element out of the oven. Placed the new element into the oven and then reattached the two wires to the new element terminals, being careful not to bend the ends of the element too much, very flexible!! Slide the element back into place and then reattached the mounting bolts. Turned all power back on to the stove and then turned the oven on and presto!, my oven is fully functional again.

I removed the screws holding the element in place. I pulled the element out from the back of the oven about 3" and then disconnected the two wires. I then reattached the two wires to the new element and pushed the element back flush with the rear of the oven. I then rescrewed the two screws that hold the element in place. That was all there was to it.. Very easy. I am 54 years old and have never done this before.. So if I can do it so can you....

I was lucky to look at other repair stories because I forgot to turn off the power!!! Nothing happen to me, but it was as simple as everybody else said. Unscrew the two screws, pull out element, unscrew another two screws and put back together in reverse order. Viola, the oven was back in working order just in time for a major event the next day. Thanks everybody for their tips and partselect for fast shipping.

I turned off the breaker, removed two screws that held the element in place, pulled it out about four inches, disconnected the screws securing the wires to the element. Removed the old element, placed the new one in the oven and reversed the procedure.