RK747G1J5 Hotpoint Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- c from Cincinnati, OH
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Bake element melted! Lucky it didn't start a fire!
The longest step in the fix was the walk downstairs to turn off the breaker.
1 nut driver to remove the element from the oven. 1 screwdriver to disconnect. Just as simple to re-install.
If you have this oven I seriously recommend the $30 expense to replace the element before it fails. It honestly went out with a white hot welder's torch sort of short circuit that could have burned my house down.
1 nut driver to remove the element from the oven. 1 screwdriver to disconnect. Just as simple to re-install.
If you have this oven I seriously recommend the $30 expense to replace the element before it fails. It honestly went out with a white hot welder's torch sort of short circuit that could have burned my house down.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from San Jose, CA
- Parts Used:
- WB44X200
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Cal Rod heating element failed
Getting the part out was easy. Turned the power off (of course) first. The outside nuts were corroded, so had to use a pair of pliers to get them off. The inside connectors were easier to get off. I had a little trouble getting the connectors on the wires. The metal part on the heating element kept wanting to bend. I finally had someone hold that in place while I made the connections. The outside screws were easy to put on. The oven now works great. I think the element was failing over a period of time, and we just didn't notice. I can't remember the last time I actually saw the element get RED hot. Works great. Thanks for your quick service and reasonable prices. Will definitely use you again, when I need parts like this. (You are now Bookmarked on my computer).
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jennifer from gambrills, MD
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench set
broken heating element
unscrewed the broken one and replaced it with the new heating element. Worked perfectly! 20+ year old oven.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Darisa from Bakersfield, CA
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bake element did not work any longer
Unscrewed old element and screwed in the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from Saint Louis, MO
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Bottom oven burner went out.
Removed two small bolt screws that held the bottom burner in place. Unscrew the two small screws that attach the oven wiring to the bottom burner. Put the bottom burner back in place and screw the two small bolt screws back in and its done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rachel from Southfield, MI
- Parts Used:
- WB44X200
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench set
Broken heating element
Turned off electricity at fuse box. Unscrewed old element and removed. Put in new element, screwed it in. Turned on electricity. Voila.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Tulsa, OK
- Parts Used:
- WB44X173
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
top element in oven was broken ,not working
Removed 4 screws and removed the old element and replaced in the reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Diana from Millbrae, CA
- Parts Used:
- WB44X200
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Heating element corroded.
I have to admit that I tried to remove the element myself but I did not have the right tool for the last two screws. If I did it would have been very easy. I ordered the part and had someone else put it in so I cheated.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Sugar Land, TX
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Heating element burned out
Turned off the breaker. Removed 2 screws and pulled the element from encasement. Removed 2 screws holding the wires to the element.
Reversed the process to install the new coil.
Done in 10 minutes
Reversed the process to install the new coil.
Done in 10 minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ernie from Gualala,Ca, CA
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
old burner had burned out and broken
removed old element and installed new, and oven is up and working like new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephanie from Glenmont, NY
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Broken Bake Element in Oven
Unscrewed face plate, unscrewed electric wires hooked to element. Cleaned out oven while I was in there...nice and clean now. Installed new element same way I took it out. Easy as 'pie'..which we'll be baking again now that the oven works.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from Andover, MA
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Bake element hot spots and deformed
Looked up mfg. and part #,looked at blow up of stove on parts select, identified element. The part came overnite. Shut down power, removed 2 screws with a nut driver, pulled element foreward to reveal 2 screws attaching wires. Replaced in reverse order, turned on power, back in service. 10 minutes tops.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Hugh from Midland, TX
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Bake Element Burned Out
It is simple.
Cut off the power. Remove racks. Remove burned out element and replace with new one.
Replace racks and turn on the power. Set the clock.
I've done this about 5 times and now keep a spare element.
Cut off the power. Remove racks. Remove burned out element and replace with new one.
Replace racks and turn on the power. Set the clock.
I've done this about 5 times and now keep a spare element.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wilfred from Freeland, WA
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bake element burnt out
Element went out on Wednesday; ordered part on Thursday; it arrived on Saturday (via regular service). Took out old part with hex screw drived, installed new and back in business.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ben from Mena, AR
- Parts Used:
- WB44X200
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Heating element brned out.
Removed two screws to release the burner, then two screws to disconnect the wiring and replace them. Then inserted the burner int position and replaced the two screws which were removed to remove the burner.
Very easy, however you will need a flashlight to see by since the back of the oven is rather dark.
Very easy, however you will need a flashlight to see by since the back of the oven is rather dark.
Was this instruction helpful to you?
Thank you for voting!