RB632G2R1 Hotpoint Range - Instructions

I removed the old drip pans, cleaned the range top, washed and installed the new drip pans and put the old pans, box and packing materials in the trash. In only 12 minutes my range top looked like new and the mess was picked up. Now, if I could just get the rest of the kitchen looking that good that fast!

Piece of cake

Turned off power to the oven at the circuit breaker. Pulled the old heating element from the back lower wall of the oven. Noted the position of the wires (right terminal attached to the red wire, left to the black wire). Removed small bolts holding the element to the wires using pliers. Attached the new element using screw driver. New element came with screws, not bolts. Pushed the element back into place and restored power. Tested to make sure everything worked. Everything works and I ran an oven cleaning cycle. Noticed that indicator light above the temperature selctor is always on now even when oven is in the OFF position. Not sure if that's related to the change or to the oven cleaning cycle I ran. In any case, oven seems to work normally.

We tried to find the replacement pans at the local hardware store and were disappointed in that although they were cheaper, they were not deep enough to handle the heating elements. We were delighted to find that the parts from PartSelect.Com were genuine GE parts... installed in minutes and were delivered VERY quickly!

I simply replaced the female part of the plug that the coil plugs in to. I figured this would do the job. I replaced the part,

I followed the instructions given to me in the package and all went well. I cut the old wires off the burnt terminal block, stripped the wires, installed the wire nuts with the shrink rap, installed the new terminal block and burner. The new burner is working great! Thanks

I simply replaced the element. HOWEVER, the most wonderful parts of this repair...Because of the pictures and closeups and descriptions I knew exactly 'what' to order! And I had the replacement in less than 24 hours. I can do some home repairs but this company provided such detailed information AND speed of delivery...that this was a no-fuss fix. I'll definitely stop by to buy, again. Thanks!

The first thing I did wrong was order the wrong part. Then later I did find the Model number on the side of the bottom drawer. I reordered the right part and turned off the electrical breaker. Removed the old element. I then installed the element in the oven with 2 screw nuts and pulled out the stove, took off the back panel and slipped the wire nuts onto the element. Very simple. I am really thankful there is a place to order the part and it came the next day after I ordered it. WHOW!

Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires, then i connect the new element and and replaced the screwes that held it in very simple and I must say Part select was very fast at getting me the correct part the first time , they have earned a spot in my Favorite list

My husband first turned the main breaker off to the stove. Pulled the stove away from wall, took off the back plate, unhooked the element and out the new one in!!

First shut off power to the range in the electrical
breaker box (its the 220 breaker) as marked.
Remove the oven door ( open part way and lift up) the
door will come off.
Remove the 2 screws that the element is attached to the
back of the oven wall. Pull element out part way and
disconnect the 2 wires. Take out element.
The new element had different connections so I cut off
the clips stripped the wires and attached to the element
connection . The element had connections that this was
possible. Push wires back into oven wall and install the
new element with the 2 screws that were removed. You
could also put on clips to the 2 wires that attach to the
element if so desired. (Eye hole clips.)

Removed oven door by holding sides and pulling upward. It's easy to remove and replace. Removed shelves by sliding back and up, then out. Removed two hex nuts with socket wrench. They are on back wall of oven and secure element to that wall. I then pulled element out about 3 inches and disconnected the two leads.

I put new element in, reconnected two leads, replace two hex nuts and was done.

Turn off power to stove at circuit breaker before starting.

Two 1/4" srews to remove the element from its mount, two 1/4" screws to remove wires and then the reverse to install new unit. Delivery was super fast and the price was half the price of the local dealers. I will certainly be a repeat customer.
Gary T.

When I told my husband I ordered the part and was going to fix it myself, he laughed and said I might not have ordered the right part for the problem and I should just buy a new stove.
The part was delivered the day before Christmas, just 3 days after I placed the order! I had read the stories of others fixing theirs and gave it a shot. It took me longer to find the tools then it did to replace the element!
I took the screws out , pulled the element toward me and disconnected the wires. Put it back the way I found it. Oven heated up in less then 5 minutes!