Models > RC749002 > Instructions

RC749002 Hotpoint Range - Instructions

Jump to:

All Instructions for the RC749002
106 - 120 of 160
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
KENNEDY from OCEAN GROVE, NJ
Parts Used:
WB30X342
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Socket set
only half of burner working
Replaced the old with the new following directions (mostly).
Was this instruction helpful to you?
Thank you for voting!
Customer:
Gerri from nashville, TN
Parts Used:
WB32X10012, WB31X5013
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Drip pans were disgusting.
Just an easy replacement. Problem was, I couldn't find the parts. The service and turn-around was fabulous!
Was this instruction helpful to you?
Thank you for voting!
Customer:
Clifford from New smyrna beach, FL
Parts Used:
WB21X36771
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
Burner constantly heated
Good directions
Was this instruction helpful to you?
Thank you for voting!
Customer:
Joseph from Baden, PA
Parts Used:
WB21X36771
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers
Front Burner,no control of.
The original controls were different for the small burners and the large burners. The replacement part fits all. Before removing wires, pay attention to writing on new and old control and replace 1 at a time. The hardest part was being sure to cut the knob stem to the correct length. Control works well.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Jone from Palmyra, VA
Parts Used:
WB44X173
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers
Broiler element not working
Some times it's not the element at all, as in this case. After rmoving the element I found the wires broke. Fortunatly I had some high temp wire left over from a earlier oven repair. I used butt splices and heat shrink tubing to repair the wires. Then I crimped on a couple of eyelets and fastened things dow.n I received a big kiss form the wife for getting the broiler fixed so fast. Maybe a little extra work, but the rewards were worth it.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Glenn from Plano, TX
Parts Used:
WB44X173
Difficulty Level:
Really Easy
Total Repair Time:
1- 2 hours
Tools:
Pliers
broil element failure
Unscrew 4 easy nuts and 1 most difficult nut, gently pull both long and short wires, at this point assure the wife that you did turn off the power.You may wish to attach a cord to short wire as it wants to vanish into the rear bowels of the oven On instruction of the wife clean the oven. Reverse dismantling procedure. Switch oven on. Bask in wives praise.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Ken from Temecula, CA
Parts Used:
WB44X173
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
Oven not getting hot to preset temp
First turn off breakers. Undo all screws and remove burner. Easy to see how to replace old part with new. Self explanatory if you follow what you have taken apart.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Myer from Cleveland, GA
Parts Used:
WB44X173
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Socket set
Broil Element burned out
Removed old element, checked continuity and element was bad, Fit new element and everything was good. No problem except my arms were not long enough!! Repairs took about 15 minutes.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Larry from Mendota, IL
Parts Used:
WB44X173
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
broiler element burnt thru
TURN OFF POWER , remove oven door & oven wire racks, remove two retaining screws in back of coil and pull the burnt coil foward enough to remove the screws that hold the wires to the coil. You may have to drop one side of the front support bracket to move coil forward.Fasten the new coil to the broiler wires with the new screws provided. Push the new coil back into place being careful not to pinch the wires in the opening. Refasten coil to the oven back with existing screws that you removed. Refasten front support.Put racks back in and put door back on.Easy fix! Easy to order, easy to install and came within days from order date. Very pleased with whole thing.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Joseph from San Antonio, TX
Parts Used:
WB32X10013, WB32X10012
Difficulty Level:
A Bit Difficult
Total Repair Time:
Less than 15 mins
Old drip pans rusted out.
Range is 45 yrs old. New drip pans are different shape. This is only place which had them and VERY GOOD price. Delivery was quick, too!
Was this instruction helpful to you?
Thank you for voting!
Customer:
Viola from Sacramento, CA
Parts Used:
WB32X10013, WB32X10012, WB31X5014, WB31X5013
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Needed to replace drip bowls & trim rings for hard to find older range top....
As easy as 1-2-3 !!! :) Lift up burners, place drip bowls down then trim rings, put burners down! Could not be faster or easier! :) I Could NOT find these parts ANYWHERE !!! :) After much aggravation, I was EXTREMELY happy to come across these parts at PartSelect, online! :) Thanks so much for the diagram, you made is sooooooo EASY to find the precise parts that I needed, now I can cook !!! :)
Was this instruction helpful to you?
Thank you for voting!
Customer:
Dave from West Hartford, CT
Parts Used:
WB32X10013, WB32X10012, WB31X5014, WB31X5013
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Drip pan replacement
Couldn't find drip pans locally that fit my stove. I came here by chance searching the internet and found the parts I needed and had them in my hands within a day or two!! Not a big parts repair story but excellent service and shipping!! Will buy from again when needed!
Was this instruction helpful to you?
Thank you for voting!
Customer:
cheryn from lynchburg, VA
Parts Used:
WB30X348
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers, Socket set
replace burner, drip bowl and ring
This was a second hand stove we have had for about 3-yrs. I noticed immediatley that the drip bowls and rings were not OEM parts & the bottom of the burners had actually been bent to fit the rings. I was very glad to find this website with a detailed diagram of the stove and parts. I intend to replace all the burners, drip bowl & rings, and then start replacing other parts as needed.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Raymond ` from Houston, TX
Parts Used:
WB44X173
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers, Screw drivers
Broiler electrical heating element burn-out.
Just re-connected the electrical. Was the exact/correct replacement part. Repair successful. Thanks.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Chuck from Ellettsville, IN
Parts Used:
WB44X173
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
Broiler Element burned out
From inside the oven after turning off the breaker I removed all of the mounting screws with a nutdriver, I removed the wire screws after taping all of the wires together with a small piece of tape to prevent them from falling back into the opening. I installed the wires with the original screws as the provided screws would not fit the holes, tightened them, removed the tape and placed the element back into the opening. I then tightened the hanging brackets, after getting them to align and then tightened the rear mounting bracket. It did help to adjust the baking rack down and leave the baking rack in place to have a place to rest my arms. The install then became a piece of cake!
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the RC749002
106 - 120 of 160