Models > RB735*04 > Instructions

RB735*04 Hotpoint Range - Instructions

Jump to:

All Instructions for the RB735*04

Customer:: Joseph from Baden, PA
Parts Used:: WB21X36771
Difficulty Level:: Easy
Total Repair Time:: 30 - 60 mins
Tools:: Pliers, Screw drivers

Front Burner,no control of.

The original controls were different for the small burners and the large burners. The replacement part fits all. Before removing wires, pay attention to writing on new and old control and replace 1 at a time. The hardest part was being sure to cut the knob stem to the correct length. Control works well.

Was this instruction helpful to you?

Customer:: Deon from Olympia, WA
Parts Used:: WB30X348
Difficulty Level:: Really Easy
Total Repair Time:: 30 - 60 mins
Tools:: Pliers, Screw drivers

Element burnt out

The repair was easy once he read the directions. The part arrived about 4 days earlier than expected. Great company.

Was this instruction helpful to you?

Customer:: James from Nashville, AR
Parts Used:: WB21X36771
Difficulty Level:: A Bit Difficult
Total Repair Time:: 1- 2 hours
Tools:: Nutdriver, Pliers, Screw drivers, Socket set, Wrench set

R had ight front control made loud noise when contacts opened.

This is twin oven range with controls at side of upper oven. Control panel was fastened with screws at top and bottom. Range has built-in hood at top which had to be disassembled to reach top screw. Once had access to top screw, eaisly removed control panel and replaced control. New control had identical connections as old control so only had to install it, break shaft to correct length, and use proper shaft adapter for knob. Remounted control panel and range worked perfectly. This would have been a very quick job except for having to deal with the built-in range hood.

Was this instruction helpful to you?

Customer:: Grady` from Titus, AL
Parts Used:: WB30X342
Difficulty Level:: A Bit Difficult
Total Repair Time:: 1- 2 hours
Tools:: Nutdriver, Screw drivers

Bad Burner

There was no burner listed like 40 yr old burner that failed. Got one the same size and connections. Cut old burner out of the stainless steel ring and new burner fit right in. New burner works great

Was this instruction helpful to you?

Customer:: Steven from Portsmouth, RI
Parts Used:: WB30X348
Difficulty Level:: Really Easy
Total Repair Time:: 30 - 60 mins
Tools:: Screw drivers

burner warped, pan didn't sit right

It would have been easy, but the screws that came with the replacement burner were too long for the ceramic insulator to fit over. Had to grind down the screws fro 3/8" long to 1/4" long. After that, piece of cake.

Was this instruction helpful to you?

Customer:: Carol from Hamilton, OH
Parts Used:: WB21X36771
Difficulty Level:: Easy
Total Repair Time:: 30 - 60 mins
Tools:: Pliers, Screw drivers

Shaft for burner control knob broke off

I flipped breaker off for electic and confirmed that power to the stove was off. I removed the 2 screws holding the control unit in place. Carefully removed all knobs and buttons and pryed the cover for the control unit off. I then removed old part, removed the wired and clipped wires to the new unit. Put cover back on - has some difficulty getting the panel back in place to line up the screws. But after a couple of attempts, was able to line up unit and put screws in place to secure. Replaced all knobs. Turn breaker back on and cooked lunch. Very easy job. Most difficult part was getting panel back in position. I would watch alignment more carefully before I removed in next time. Easy home repair for Women...not sure about my man?

Was this instruction helpful to you?

Customer:: KENNEDY from OCEAN GROVE, NJ
Parts Used:: WB30X342
Difficulty Level:: A Bit Difficult
Total Repair Time:: 30 - 60 mins
Tools:: Screw drivers, Socket set

only half of burner working

Replaced the old with the new following directions (mostly).

Was this instruction helpful to you?

All Instructions for the RB735*04